FAN3111E Fairchild Semiconductor, FAN3111E Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/2/252/fairchild_semiconductor_sml.jpg)
FAN3111E
Manufacturer Part Number
FAN3111E
Description
The FAN3111 1A gate driver is designed to drive an N-channel enhancement-mode MOSFET in low-side switching applications
Manufacturer
Fairchild Semiconductor
Datasheet
1.FAN3111E.pdf
(18 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FAN3111ESX
Manufacturer:
FSC
Quantity:
3 000
Company:
Part Number:
FAN3111ESX
Manufacturer:
Fairchild Semiconductor
Quantity:
81 749
© 2008 Fairchild Semiconductor Corporation
FAN3111 • Rev. 1.0.2
The output-pin slew rate is determined by V
and the load on the output. It is not user adjustable, but
if a slower rise or fall time at the MOSFET gate is
needed, a series resistor can be added.
V
To enable this IC to turn a power device on quickly, a
local, high-frequency, bypass capacitor C
ESR and ESL should be connected between the VDD
and GND pins with minimal trace length. This capacitor
is in addition to bulk electrolytic capacitance of 10µF to
47µF often found on driver and controller bias circuits.
A typical criterion for choosing the value of C
keep the ripple voltage on the V
this is achieved with a value ≥ 20 times the equivalent
load capacitance C
Ceramic capacitors of 0.1µF to 1µF or larger are
common choices, as are dielectrics, such as X5R and
X7R, which have good temperature characteristics and
high pulse current capability.
If circuit noise affects normal operation, the value of
C
may be split into two capacitors. One should be a larger
value, based on equivalent load capacitance, and the
other a smaller value, such as 1-10nF, mounted closest
to the VDD and GND pins to carry the higher-frequency
components of the current pulses.
Layout and Connection Guidelines
The FAN3111 incorporates fast reacting input circuits,
short propagation delays, and output stages capable of
delivering current peaks over 1A to facilitate voltage
transition times from under 10ns to over 100ns. The
following layout and connection guidelines are strongly
recommended:
BYP
DD
Figure 38.
Keep high-current output and power ground paths
separate from logic input signals and signal ground
paths. This is especially critical when dealing with
TTL-level logic thresholds.
Bypass Capacitor Guidelines
may be increased to 50-100 times the C
MillerDrive™ Output Architecture
EQV
, defined here as Q
DD
supply ≤5%. Often
BYP
EQV
DD
with low
BYP
gate
voltage
or C
/V
is to
BYP
DD
.
13
Figure 39 shows the pulsed gate-drive current path
when the gate driver is supplying gate charge to turn the
MOSFET on. The current is supplied from the local
bypass capacitor, C
the MOSFET gate and to ground. To reach the high
peak currents possible, the resistance and inductance in
the path should be minimized. The localized C
contain the high peak-current pulses within this driver-
MOSFET circuit, preventing them from disturbing the
sensitive analog circuitry in the PWM controller.
Figure 40 shows the current path when the gate driver
turns the MOSFET off. Ideally, the driver shunts the
current directly to the source of the MOSFET in a small
circuit loop. For fast turn-off times, the resistance and
inductance in this path should be minimized.
Figure 39.
Figure 40.
Keep the driver as close to the load as possible to
minimize the length of high-current traces. This
reduces the series inductance to improve high-
speed switching, while reducing the loop area that
can radiate EMI to the driver inputs and other
surrounding circuitry.
Many high-speed power circuits can be susceptible
to noise injected from their own output or other
external sources, possibly causing output re-
triggering. These effects can be especially obvious
if the circuit is tested in breadboard or non-optimal
circuit layouts with long input, enable, or output
leads. For best results, make connections to all pins
as short and direct as possible.
The turn-on and turn-off current paths should be
minimized as discussed in the following sections.
PWM
PWM
C
C
Current Path for MOSFET Turn-On
Current Path for MOSFET Turn-Off
BYP
BYP
BYP
, and flows through the driver to
V
V
DD
DD
FAN3111
FAN3111
V
V
DS
DS
www.fairchildsemi.com
BYP
acts to