DSPIC30F3011 Microchip Technology Inc., DSPIC30F3011 Datasheet - Page 67
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
DSPIC30F3011
Manufacturer Part Number
DSPIC30F3011
Description
Dspic30f3010/3011 Enhanced Flash 16-bit Digital Signal Controller
Manufacturer
Microchip Technology Inc.
Datasheet
1.DSPIC30F3011.pdf
(220 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F3011-20E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
DSPIC30F3011-20I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F3011-30I/ML
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
DSPIC30F3011-30I/P
Manufacturer:
Microchip
Quantity:
927
Company:
Part Number:
DSPIC30F3011-30I/PT
Manufacturer:
MICROCHIP
Quantity:
316
Company:
Part Number:
DSPIC30F3011-30I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F3011-30I/PT
Manufacturer:
MICROCHI
Quantity:
20 000
Company:
Part Number:
DSPIC30F3011T-20E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
DSPIC30F3011T-20I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F3011T-30I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
9.4
The 16-bit timer has the ability to generate an interrupt
on period match. When the timer count matches the
Period register, the T1IF bit is asserted and an interrupt
will be generated, if enabled. The T1IF bit must be
cleared in software. The timer interrupt flag T1IF is
located in the IFS0 control register in the Interrupt
Controller.
When the Gated Time Accumulation mode is enabled,
an interrupt will also be generated on the falling edge of
the gate signal (at the end of the accumulation cycle).
Enabling an interrupt is accomplished via the
respective Timer Interrupt Enable bit, T1IE. The Timer
Interrupt Enable bit is located in the IEC0 control
register in the Interrupt Controller.
9.5
Timer1, when operating in Real-Time Clock (RTC)
mode, provides time-of-day and event time stamping
capabilities. Key operational features of the RTC are:
• Operation from 32 kHz LP oscillator
• 8-bit prescaler
• Low power
• Real-Time Clock Interrupts
These Operating modes are determined by setting the
appropriate bit(s) in the T1CON control register
FIGURE 9-2:
© 2007 Microchip Technology Inc.
C1 = C2 = 18 pF; R = 100K
C1
C2
Timer Interrupt
Real-Time Clock
32.768 kHz
XTAL
R
RECOMMENDED
COMPONENTS FOR
TIMER1 LP OSCILLATOR
RTC
SOSCI
SOSCO
dsPIC30FXXXX
Confidential
9.5.1
When the TON = 1, TCS = 1 and TGATE = 0, the timer
increments on the rising edge of the 32 kHz LP oscilla-
tor output signal, up to the value specified in the Period
register, and is then reset to ‘0’.
The TSYNC bit must be asserted to a logic ‘0’
(Asynchronous mode) for correct operation.
Enabling LPOSCEN (OSCCON<1>) will disable the
normal Timer and Counter modes and enable a timer
carry-out wake-up event.
When the CPU enters Sleep mode, the RTC will
continue to operate, provided the 32 kHz external
crystal oscillator is active and the control bits have not
been changed. The TSIDL bit should be cleared to ‘0’
in order for RTC to continue operation in Idle mode.
9.5.2
When an interrupt event occurs, the respective
interrupt flag, T1IF, is asserted and an interrupt will be
generated, if enabled. The T1IF bit must be cleared in
software. The respective Timer interrupt flag, T1IF, is
located in the IFS0 status register in the Interrupt
Controller.
Enabling an interrupt is accomplished via the
respective Timer Interrupt Enable bit, T1IE. The Timer
Interrupt Enable bit is located in the IEC0 control
register in the Interrupt Controller.
dsPIC30F3010/3011
RTC OSCILLATOR OPERATION
RTC INTERRUPTS
DS70141D-page 65