tc59lm836dkg TOSHIBA Semiconductor CORPORATION, tc59lm836dkg Datasheet - Page 11

• Manufacturer Part Number: tc59lm836dkg
• Description: 288mbits Network Fcram2 ? 2,097,152-words ? 4 Banks ? 36-bits
• Manufacturer: TOSHIBA Semiconductor CORPORATION

(10) These parameters are measured at t
(11) These parameters are measured at V
AC TEST CONDITIONS
NOTES:
(1) Transition times are measured between V
(2) If the result of nominal calculation with regard to t
(3) These parameters are measured from the differential clock (CLK and CLK ) AC cross point.
(4) These parameters are measured from signal transition point of DS crossing V
(5) The t
(6) Low Impedance State is specified at V
(7) High Impedance State is specified where output buffer is no longer driven.
(8) These parameters depend on the clock jitter. These parameters are measured at stable clock.
(9) Output timing is measured by using Normal driver strength at V
V
V
V
V
V
Vr
V
SLEW
V
IH (min)
IL (max)
REF
TT
SWING
ID
OTR
Transition (rise and fall) of input signals have a fixed slope.
rounded up to the nearest decimal place.
(i.e., t
The t
In such case, the average interval of eight consecutive Auto-Refresh commands has to be more than 400 ns
always. In other words, the number of Auto-Refresh cycles which can be performed within 3.2 µs (8 × 400 ns)
is to 8 times in the maximum.
Output timing is measured by using Strong driver strength at V
are specified as below for all speed version.
t
specified as below for all speed version.
t
SYMBOL
CKQS
DS
(AC)
V
(MIN) = 0.4 ns , t
SWING
REFI (max)
REFI (min)
DQSS
SLEW = (V
(MIN/MAX) = −0.6ns / 0.6ns, t
Input High Voltage (minimum)
Input Low Voltage (maximum)
Input Reference Voltage
Termination Voltage
Input Signal Peak to Peak Swing
Differential Clock Input Reference Level
Input Differential Voltage
Input Signal Minimum Slew Rate
Output Timing Measurement Reference Voltage
= 0.8 × t
applies to both burst refresh method and distributed refresh method.
IH min
applies to equally distributed refresh method.
∆T
CK
DH
(AC) − V
, t
V
V
CK
(MIN) = 0.4 ns
DDQ
SS
= 3.3 ns, 0.8 × 3.3 ns = 2.64 ns is rounded up to 2.7 ns.)
IL max
∆T
PARAMETER
(AC))/∆T
CK
AC
DDQ
DDQ
= minimum ∼ 6.0ns. When t
(MIN/MAX) = −0.65ns / 0.65ns
IH min
/2 ± 0.1 V from steady state.
V
V
V
IH min
REF
IL max
= 1.7 V∼1.9 V. Both t
(DC) and V
(AC)
(AC)
CK
contains more than one decimal place, the result is
IL max
DDQ
DDQ
(DC).
DS
CK
= 1.4 V~1.6 V.
= 1.7 V ∼ 1.9 V.
V
V
and t
is longer than 6.0ns, these parameters
REF
REF
V
V
V
VALUE
V
X
Measurement point
DDQ
DDQ
TC59LM836DKG-33,-40
0.8
1.0
2.5
REF
(AC)
Output
+ 0.2
− 0.2
DH
/2
/2
REF
at V
level.
AC Test Load
2005-11-08 11/65
25 Ω
DDQ
UNIT
V/ns
V
V
V
V
V
V
V
V
= 1.4 V∼1.6 V are
V
TT
Rev 1.4
NOTES
9