DS80C320-ECD DALLAS [Dallas Semiconductor], DS80C320-ECD Datasheet - Page 173
DS80C320-ECD
Manufacturer Part Number
DS80C320-ECD
Description
High-Speed Microcontroller User Guide
Manufacturer
DALLAS [Dallas Semiconductor]
Datasheet
1.DS80C320-ECD.pdf
(175 pages)
- Current page: 173 of 175
- Download datasheet (2Mb)
SECTION 17: TROUBLESHOOTING
DEVICE OPERATES AT 1/3 OF CRYSTAL SPEED
The High-Speed Microcontroller Family operates from the primary or fundamental mode of the external
crystal. Many off-the-shelf high-frequency crystals are specified to operate from their third overtone.
When used with a High-Speed Microcontroller, these crystals will resonate in their primary mode, which
will appear to be 1/3 of the rated crystal speed. Make sure that any crystals used will operate at their
rated speed in primary mode.
DEVICE RESETS FOR NO REASON
During the debugging process, it may be necessary to isolate the cause of an unexpected device reset.
Because resets are initiated by a limited number of sources, it is relatively easy to determine their source
by interrogating a few bits. These bits should be interrogated early in the code following a reset to
determine its source. As a debug tool, software could set the state of one or more port pins to indicate the
type of reset to the designer. Note that power supply problems or glitches will appear as unplanned
power-on resets.
ACCESS TO INTERNAL MOVX SRAM IS UNSUCCESSFUL
The internal MOVX SRAM available on some members of the High-Speed Microcontroller Family is
disabled after any reset. To enable the on-chip SRAM, the software should configure the Data Memory
Enable bits (PMR.1-0) as needed.
When V
battery voltage is greater than V
access is denied. Make sure that the battery voltage remains below the minimum V
REAL-TIME CLOCK DOES NOT OPERATE OR KEEP ACCURATE TIME
The state of the real-time clock (RTC) used on the DS87C530 is undefined following a no-battery reset or
battery attach. The RTC oscillator must be enabled by setting the RTCE bit (RTCC.0) for the RTC to
work.
The RTC is guaranteed to a minimum accuracy of ± 2 minutes per month over the rated temperature and
voltage specifications. If the time is found to be less accurate than this, it is most likely due to the
selection of crystal. Make sure that the RTC crystal is 32.768 kHz, and either 12.5 pF or 6 pF
capacitance. The 12/6 bit (TRIM.6) setting should correspond to the crystal in use. Unlike other crystals,
external load capacitors should not be used with the RTC. These will seriously distort the accuracy of the
clock. Additional information on design considerations with the RTC can be found in Applications Note
79, Using the DS87C530 Real Time Clock.
Power–on reset
Watchdog reset
External reset
SOURCE
CC
drops below V
WDCON.6
POR BIT
1
0
0
BAT
WTRF BIT
WDCON.3
0
1
0
, access to the SRAM is disabled to prevent corruption of the data. If the
RST
, this means that the processor may continue to operate while SRAM
173 of 175
High-Speed Microcontroller User’s Guide
RST
.
.
Related parts for DS80C320-ECD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller, 8051 Comp., 4 8-Bit I/O Ports, 64K ROM/RAM, 25 MHz, 5 V, PLCC44
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller, 8051 Comp., 4 8-Bit I/O Ports, 64K ROM/RAM, 25 MHz, 5 V, PDIP40
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
High Resolution Temperature Measurement with Dallas Direct-to-Digital Temperature Sensors
Manufacturer:
Dallas Semiconductor
Part Number:
Description:
32.768kHz Temperature-Compensated Crystal Oscillator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
3.3 volt micromonitor, tolerance 20%
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Ultra3 LVD/SE SCSI Terminator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
SCSI Terminator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet: