DS80C320-ECD DALLAS [Dallas Semiconductor], DS80C320-ECD Datasheet - Page 97
DS80C320-ECD
Manufacturer Part Number
DS80C320-ECD
Description
High-Speed Microcontroller User Guide
Manufacturer
DALLAS [Dallas Semiconductor]
Datasheet
1.DS80C320-ECD.pdf
(175 pages)
- Current page: 97 of 175
- Download datasheet (2Mb)
SPEED REDUCTION
The High-Speed Microcontroller is a fully CMOS 8051 compatible microcontroller.
significantly less power than other 8051 versions because it is more efficient. As an average, software
will run 2.5 times faster on the High-Speed Microcontroller than on other 8051 derivatives. Thus the
same job can be accomplished by slowing down the crystal by a factor of 2.5. For example, an existing
8051 design that runs at 12 MHz can run at approximately 4.8 MHz on the High-Speed Microcontroller.
At this reduced speed, the High-Speed Microcontroller will have lower power consumption than an 8051,
yet perform the same job.
Using the 2.5X factor, Table 7-2 shows the approximate speed at which the High-Speed Microcontroller
can accomplish the same work as an 8051. The exact improvement will vary depending on the actual
instruction mix. Available crystal speeds must also be considered. Refer to Section 16 for information
on instruction timing.
CRYSTAL VS MIPS COMPARISON Table 7-2
POWER MANAGEMENT MODES
Power consumption in CMOS microcontrollers is a function of operating frequency.
Management Mode (PMM) feature, available with some members of the High-Speed Microcontroller
family, allows software to dynamically match operating frequency and current consumption with the need
for processing power. Instead of the default 4 clocks per machine cycle, power management mode 1
(PMM1) and power management mode 2 (PMM2) utilize 64 and 1024 clocks per cycle respectively to
conserve power.
A number of special features have been added to enhance the function of the power management modes.
The switchback feature allows the device to almost instantaneously return to divide by 4 mode upon
acknowledgment of an external interrupt or a falling edge on a serial port receiver pin. The advantages of
this become apparent when one calculates the increased interrupt service time of a device operating in
PMM. In addition, a device operating in PMM would normally be unable to sample an incoming serial
transmission to properly receive it. The switchback feature, explained below, allows a device to return to
divide by 4 operation in time to receive incoming serial port data and process interrupts with no loss in
performance.
The DS87C520 and DS87C530 incorporate a Status register (STATUS;C5h) to prevent the device from
accidentally reducing the clock rate during the servicing of an external interrupt or serial port activity.
This register can be interrogated to determine if a high priority, low priority, or power fail interrupt is in
progress, or if serial port activity is occurring. Based on this information the software can delay or reject
a planned change in the clock divider rate.
CRYSTAL SPEED
ORIGINAL 8051
11.0592 MHz
14.318 MHz
3.57 MHz
7.37 MHz
16 MHz
20 MHz
24 MHz
33 MHz
40 MHz
97 of 175
0.3
0.6
0.9
1.2
1.3
1.6
2.0
2.7
3.3
MIPS
HIGH–SPEED MICROCONTROLLER
High-Speed Microcontroller User’s Guide
CRYSTAL SPEED
13.2 MHz
1.4 MHz
2.9 MHz
4.4 MHz
5.7 MHz
6.4 MHz
9.6 MHz
16 MHz
8 MHz
The Power
It can use
Related parts for DS80C320-ECD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller, 8051 Comp., 4 8-Bit I/O Ports, 64K ROM/RAM, 25 MHz, 5 V, PLCC44
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller, 8051 Comp., 4 8-Bit I/O Ports, 64K ROM/RAM, 25 MHz, 5 V, PDIP40
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
High Resolution Temperature Measurement with Dallas Direct-to-Digital Temperature Sensors
Manufacturer:
Dallas Semiconductor
Part Number:
Description:
32.768kHz Temperature-Compensated Crystal Oscillator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
3.3 volt micromonitor, tolerance 20%
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Ultra3 LVD/SE SCSI Terminator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
SCSI Terminator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet: