PEB20534H-10 SIEMENS [Siemens Semiconductor Group], PEB20534H-10 Datasheet - Page 122
PEB20534H-10
Manufacturer Part Number
PEB20534H-10
Description
DMA Supported Serial Communication Controller with 4 Channels DSCC4
Manufacturer
SIEMENS [Siemens Semiconductor Group]
Datasheet
1.PEB20534H-10.pdf
(442 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PEB20534H-10-V2.1
Manufacturer:
INF
Quantity:
5 510
Company:
Part Number:
PEB20534H-10-V2.1
Manufacturer:
PHILIPS
Quantity:
5 510
Company:
Part Number:
PEB20534H-10V2.1
Manufacturer:
MICRON
Quantity:
78
- Current page: 122 of 442
- Download datasheet (2Mb)
PEB 20534
Multi Function Port (MFP)
The same mechanism as for selecting a slave for transmission (separate select lines or
special commands) may also be used to promote the role of the master to another device
in the network. In this case the previous master and the future master (previous slave)
will have to toggle their operating mode (SSCMS) and the direction of their port pins (see
description above).
Chip Select Control:
There are 4 chip select pins associated with the SSC port: MCS0 to MCS3. The four chip
select lines are automatically activated at the beginning of a transfer and deactivated
again after the transfer has ended. Activation of a chip enable line always begins one
half bit time before the first data bit is output at the MTSR pin, and the deactivation
(except for the continuous transfers) is performed one half bit time after the last bit of the
transfer has been transmitted/received completely.
The chip select lines are selected by the control bits ASEL0 to ASEL3 of the SSC Chip
Select Enable register SSCCSE (refer to “SSC Registers Description” on page 355).
By setting any of these bits to 0, the corresponding chip select port will be asserted when
transmitting data. All other bits of the SSCCSE register have to be set to ‘0‘.
6.2.1.3
Operational Mode: Half Duplex Operation:
In a half duplex configuration only one data line is necessary for both receiving and
transmitting of data. The data exchange line is connected to both pins MTSR and MRST
of each device, the clock line is connected to the MCLK pin.
The master device controls the data transfer by generating the shift clock, while the slave
devices receive it. Due to the fact that all transmit and receive pins are connected to the
one data exchange line, serial data may be moved between arbitrary stations.
Similar to full duplex mode there are
on the data exchange
two ways to avoid collisions
line:
• only the transmitting device may enable its transmit pin driver
• the non-transmitting devices use open drain output and only send ones.
Since the data inputs and outputs are connected together, a transmitting device will clock
in its own data at the input pin (MRST for a master device, MTSR for a slave). This allows
to detect any corruptions on the common data exchange line, where the Rx data is not
equal to the Tx data.
Semiconductor Group
122
Data Sheet 09.98
Related parts for PEB20534H-10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
Part Number:
Description:
HiRel Silicon Schottky Diode (HiRel Discrete and Microwave Semiconductor Medium barrier diodes for detector and mixer applications)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAs-Infrarot-Sendediode GaAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAlAs-Infrarot-Sendediode GaAlAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet: