STM32F101X6_08 STMICROELECTRONICS [STMicroelectronics], STM32F101X6_08 Datasheet - Page 27

• Manufacturer Part Number: STM32F101X6_08
• Description: Access line, advanced ARM-based 32-bit MCU with Flash memory, six 16-bit timers, ADC and seven communication interfaces
• Manufacturer: STMICROELECTRONICS [STMicroelectronics]

STM32F101xx
5.2
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 5: Current
damage to the device. These are stress ratings only and functional operation of the device
at these conditions is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Table 4.
1. All main power (V
2. I
Table 5.
1. All main power (V
2. I
3. Negative injection disturbs the analog performance of the device. See note in
4. When several inputs are submitted to a current injection, the maximum ΣI
|V
V
I
V
INJ(PIN)
ΣI
supply, in the permitted range.
maximum is respected. If V
externally to the I
induced by V
supply, in the permitted range.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
characteristics.
positive and negative injected currents (instantaneous values). These results are based on
characterization with ΣI
Symbol
SSX
INJ(PIN)
INJ(PIN)
|∆V
ESD(HBM)
DD
Symbol
INJ(PIN)
V
I
I
VDD
VSS
DDx
I
− V
IN
− V
IO
SS
(2)(3)
must never be exceeded (see
must never be exceeded. This is implicitly insured if V
|
SS
(2)
|
Voltage characteristics
Current characteristics
IN
External main supply voltage (including
V
Input voltage on five volt tolerant pin
Input voltage on any other pin
Variations between different power pins
Variations between all the different ground
pins
Electrostatic discharge voltage (human
body model)
<V
DDA
characteristics, and
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRST pin
Injected current on High-speed external OSC_IN and Low-
speed external OSC_IN pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
INJ(PIN)
DD
DD
SS
.
, V
, V
and V
DDA
DDA
INJ(PIN)
IN
value. A positive injection is induced by V
>V
) and ground (V
) and ground (V
IN
DD
DD
maximum cannot be respected, the injection current must be limited
)
maximum current injection on four I/O port pins of the device.
(1)
while a negative injection is induced by V
Ratings
DD
Table 5: Current
SS
Table 6: Thermal characteristics
power lines (source)
SS
SS
ground lines (sink)
, V
, V
Ratings
SSA
SSA
(2)
) pins must always be connected to the external power
) pins must always be connected to the external power
(4)
(2)
characteristics). This is implicitly insured if V
IN
maximum is respected. If V
(1)
(1)
Table 4: Voltage
see
maximum ratings (electrical
IN
V
V
>V
SS
SS
Section 5.3.11: Absolute
–0.3
Min
DD
50
50
INJ(PIN)
− 0.3
− 0.3
IN
while a negative injection is
<V
INJ(PIN)
sensitivity)
(4)
Electrical characteristics
Section 5.3.16: 12-bit ADC
SS
is the absolute sum of the
.
may cause permanent
value. A positive
V
characteristics,
DD
+5.5
Max
4.0
50
50
+0.3
Max.
± 25
150
150
− 25
± 5
± 5
± 5
25
IN
maximum
IN
Unit
mV
Unit
mA
V
27/74