EMC6D100-DK SMSC [SMSC Corporation], EMC6D100-DK Datasheet - Page 34
EMC6D100-DK
Manufacturer Part Number
EMC6D100-DK
Description
ENVIRONMENTAL MONITORING AND CONTROL DEVICE WITH AUTOMATIC FAN CAPABILITY
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.EMC6D100-DK.pdf
(75 pages)
- Current page: 34 of 75
- Download datasheet (593Kb)
7.4.3
SMSC EMC6D100/EMC6D101
SPIN UP
When a fan is being started from a stationary state, the part will cause the fan to “spin up” by going to
100% duty cycle for a programmable amount of time to overcome the inertia of the fan. Following this spin
up time, the fan will go to a duty cycle computed by the auto fan algorithm.
During spin-up, the PWM duty cycle is reported as 0%.
To limit the spin-up time and thereby reduce fan noise, the part uses feedback from the tachometers to
determine when each fan has started spinning properly. The following tachometer feedback is included
into the auto fan algorithm during spin-up. This feature defaults to enabled; it can be disabled by clearing
bit 4 of the Configuration register (7Fh). If disabled, the all fans go to 100% duty cycle for the duration of
their associated spin up time. Note that the Tachometer x minimum registers must be programmed to a
value less than FFFFh in order for the spin up reduction to work properly.
1.
2.
3.
The PWM goes to 100% duty cycle until the tachometer reading register is below the minimum limit,
or the spin-up time expires, whichever comes first.
tachometer enters the valid count range, unless the spin up time expires. If the spin up expires before
the tachometer enters the valid range, an interrupt status bit will be set once spin-up expires. Note
that more than one tachometer may be associated with a PWM, in which case all tachometers
associated with a PWM must be in the valid range for spin-up to end.
The tachometer reading register always gives the actual reading of the tachometer input.
No interrupt bits are set during spin-up.
PWM
Duty
Cycle
MAX
MIN
MIN or OFF when
PWM may be at
below MIN temp
FIGURE 7.2 - AUTOMATIC FAN CONTROL
Hysteresis
DATASHEET
Spin Up
MIN
Page 34
Temperature
This causes spin-up to continue until the
MAX
Environmental Monitoring and Control Device
Rev. 09-09-04
Datasheet
Related parts for EMC6D100-DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: