EMC6D100-DK SMSC [SMSC Corporation], EMC6D100-DK Datasheet - Page 52
EMC6D100-DK
Manufacturer Part Number
EMC6D100-DK
Description
ENVIRONMENTAL MONITORING AND CONTROL DEVICE WITH AUTOMATIC FAN CAPABILITY
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.EMC6D100-DK.pdf
(75 pages)
- Current page: 52 of 75
- Download datasheet (593Kb)
8.18.2 BIT [4] PWM INVERT
8.18.3 BIT [3] RESERVED
8.18.4 BITS [2:0] SPIN UP
SMSC EMC6D100/EMC6D101
limits and parameters for the zone that requires the highest PWM duty cycle, as computed by the auto fan
algorithm.
When in manual control mode, the Current PWM Duty Registers (30h-32h) become Read/Write. It is then
possible to control the PWM outputs with software by writing to these registers. See Current PWM Duty
Registers description.
When the fan is disabled (100) the corresponding PWM output is driven low (or high, if inverted).
Zone 1:
Zone 2:
Zone 3:
Bit [4] inverts the PWM output. If set to 1, 100% duty cycle will yield an output that is low for 255 clocks
and high for 1 clock. If set to 0, 100% duty cycle will yield an output that is high for 255 clocks and low for 1
clock.
Bits [2:0] specify the ‘spin up’ time for the fan. When a fan is being started from a stationary state, the
PWM output is held at 100% duty cycle for the time specified in the table below before scaling to a lower
speed. Note: during spin-up, the PWM pin is forced high (OD) for the duration of the spin-up time.
Note: To reduce the spin-up time, the part uses feedback from the tachometers to determine when each
fan has started spinning properly. Spin up for a PWM will end when the tachometer reading register is
below the minimum limit, or the spin-up time expires, whichever comes first. All tachs associated with a
PWM must be below min for spin-up to end. This feature can be disabled by clearing bit 4 of the
Configuration register (7Fh). If disabled, the all fans go on full for the duration of their associated spin up
time. Note that the Tachx minimum registers must be programmed to a value less than FFFFh in order for
the spin up reduction to work properly.
External Diode 1 (processor)
Internal Sensor
External Diode 2
000
001
010
011
100
101
110
111
ZON[7:5]
Fan on zone 1 auto
Fan on zone 2 auto
Fan on zone 3 auto
Fan always on full
Fan disabled
Fan controlled by hottest of zones 2,3
Fan controlled by hottest of zones 1,2,3
Fan manually controlled
DATASHEET
Table 8.6 - Fan Zone Setting
FAN CONFIGURATION
Page 52
Environmental Monitoring and Control Device
Rev. 09-09-04
Datasheet
Related parts for EMC6D100-DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: