ATSAM3X4EA-AU Atmel, ATSAM3X4EA-AU Datasheet - Page 757
ATSAM3X4EA-AU
Manufacturer Part Number
ATSAM3X4EA-AU
Description
ARM Microcontrollers - MCU QFP144,GREEN, IND TEMP, MRL A
Manufacturer
Atmel
Datasheet
1.ATSAM3X8EA-AU.pdf
(1467 pages)
Specifications of ATSAM3X4EA-AU
Rohs
yes
Core
ARM Cortex M3
Processor Series
SAM3X
Data Bus Width
32 bit
Maximum Clock Frequency
84 MHz
Program Memory Size
256 KB
Data Ram Size
64 KB
On-chip Adc
Yes
Operating Supply Voltage
2.4 V to 3.6 V
Operating Temperature Range
- 40 C to +85 C
Package / Case
LQFP-144
Mounting Style
SMD/SMT
Factory Pack Quantity
60
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 757 of 1467
- Download datasheet (8Mb)
35.4.3
35.5
35.5.1
35.5.2
35.5.2.1
11057B–ATARM–28-May-12
11057B–ATARM–28-May-12
UART Operations
Interrupt Source
Baud Rate Generator
Receiver
Receiver Reset, Enable and Disable
The UART interrupt line is connected to one of the interrupt sources of the Nested Vectored
Interrupt Controller (NVIC). Interrupt handling requires programming of the NVIC before config-
uring the UART.
The UART operates in asynchronous mode only and supports only 8-bit character handling (with
parity). It has no clock pin.
The UART is made up of a receiver and a transmitter that operate independently, and a common
baud rate generator. Receiver timeout and transmitter time guard are not implemented. How-
ever, all the implemented features are compatible with those of a standard USART.
The baud rate generator provides the bit period clock named baud rate clock to both the receiver
and the transmitter.
The baud rate clock is the master clock divided by 16 times the value (CD) written in
UART_BRGR (Baud Rate Generator Register). If UART_BRGR is set to 0, the baud rate clock is
disabled and the UART remains inactive. The maximum allowable baud rate is Master Clock
divided by 16. The minimum allowable baud rate is Master Clock divided by (16 x 65536).
Figure 35-2. Baud Rate Generator
After device reset, the UART receiver is disabled and must be enabled before being used. The
receiver can be enabled by writing the control register UART_CR with the bit RXEN at 1. At this
command, the receiver starts looking for a start bit.
The programmer can disable the receiver by writing UART_CR with the bit RXDIS at 1. If the
receiver is waiting for a start bit, it is immediately stopped. However, if the receiver has already
detected a start bit and is receiving the data, it waits for the stop bit before actually stopping its
operation.
MCK
Baud Rate
16-bit Counter
=
----------------------- -
16
CD
MCK
CD
OUT
0
CD
>1
1
0
Divide
by 16
Baud Rate
Receiver
Sampling Clock
Clock
SAM3X/A
SAM3X/A
757
757
Related parts for ATSAM3X4EA-AU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Development Boards & Kits - ARM EVAL KIT SAM3X & SAM3A series
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: