AT89LP51ED2-20MU Atmel, AT89LP51ED2-20MU Datasheet - Page 19

• Manufacturer Part Number: AT89LP51ED2-20MU
• Description: 8-bit Microcontrollers - MCU 64KB 20MHz 2.4V-5.5V
• Manufacturer: Atmel

Specifications of AT89LP51ED2-20MU

• Rohs: yes
• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 20 MHz
• Program Memory Size: 64 KB
• Data Ram Size: 256 B
• On-chip Adc: Yes
• Operating Supply Voltage: 2.4 V to 5.5 V
• Operating Temperature Range: - 40 C to + 85 C
• Package / Case: VQFN-44
• Mounting Style: SMD/SMT
• Data Rom Size: 4 KB
• Interface Type: 2-Wire, SPI, UART
• Number Of Programmable I/os: 36
• Number Of Timers: 3
• Processor Series: AT89x
• Program Memory Type: Flash
• Factory Pack Quantity: 360

Table 3-3.
Notes:
3714A–MICRO–7/11
DPU
WS
XRS
EXTRAM
DISALE
Symbol
1-0
AUXR = 8EH
Not Bit Addressable
Bit
2-0
1. WS1 is only available in Fast mode. WS1 is forced to 0 in Compatibility mode.
Function
Disable Weak Pull-up. When DPU = 0 all I/O ports in quasi-bidirectional mode have their weak pull-up enabled. When
DPU = 1 all I/O ports in quasi-bidirectional mode have their weak pull-up disabled to reduce power consumption.
Wait State Select. Determines the number of wait states inserted into external memory accesses.
WS1
0
0
1
1
XRAM Size. Selects the size of the on-chip extra RAM (EDATA)
XRS2
0
0
0
0
1
1
1
External RAM Enable. When EXTRAM = 0, MOVX instructions can access the internally mapped portions of the
address space (Extra RAM and EEPROM). Accesses to addresses above internally mapped memory will access
external memory. Set EXTRAM = 1 to bypass the internal memory and map the entire 64KB address space to external
memory. The default state of EXTRAM is set by a user configuration fuse. See
ALE Output. When AO = 0 the ALE pulse is active at 1/3 of the system clock frequency in Compatibility mode and 1/2 of
the system clock frequency in Fast mode. When AO = 1 the ALE is inactive (high) unless an external memory access
occurs. AO must be set to use P4.4 as a general I/O.
AUXR
DPU
7
– Auxiliary Control Register
WS0
0
1
0
1
XRS1
0
0
1
1
0
0
1
strobe is required, the application can scale the system clock with the clock divider to meet the
requirements (See
WS1
6
(1)
Wait States
0
1
2
3
XRS0
0
1
0
1
0
1
–
WS0
5
Section 6.8 on page
RD / WR Strobe Width
1 x t
2 x t
2 x t
3 x t
EDATA Size (bytes)
256
512
768 (default)
1024
1792
2048
Reserved
CYC
CYC
CYC
CYC
(Fast); 3 x t
(Fast); 15 x t
(Fast)
(Fast)
AT89LP51RD2/ED2/ID2 Preliminary
XRS2
4
CYC
CYC
49).
(Compatibility)
(Compatibility)
XRS1
3
XRS0
2
Section 24.2 on page
ALE to RD / WR Setup
1 x t
1 x t
2 x t
2 x t
Address Range
0000H–00FFH
0000H–01FFH
0000H–02FFH
0000H–03FFH
0000H–06FFH
0000H–07FFH
CYC
CYC
CYC
CYC
Reset Value = 0000 10X0B
(Fast); 1.5 x t
(Fast); 1.5 x t
(Fast)
(Fast)
EXTRAM
1
CYC
CYC
190.
(Compatibility)
(Compatibility)
AO
0
19