L6566A STMicroelectronics, L6566A Datasheet - Page 38

• Manufacturer Part Number: L6566A
• Description: IC CTRLR OVP UVLO 16SOIC
• Manufacturer: STMicroelectronics

Specifications of L6566A

• Output Isolation: Isolated
• Frequency Range: 93 ~ 107kHz
• Voltage - Input: 8 ~ 23 V
• Power (watts): 750mW
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Output Current: 800 mA
• Output Power: 750 mW
• Input Voltage: 8 V to 23 V
• Operating Temperature Range: - 40 C to + 150 C
• Mounting Style: SMD/SMT
• Duty Cycle (max): 75 %
• Universal Input Mains Range: 90÷264Vac - Frequency 45 ÷ 65 Hz
• Output Voltage: 19 V@4 A continuous operation
• Mains Harmonics: Acc. to EN61000-3-2 Class-D
• St-by Mains Consumption: Less than 0.25 W @265Vac
• Overall Efficiency: Better than 86%
• Emi: According to EN55022-Class-B
• Safety: According to EN60950
• Low Profile Design: 25 mm maximum height
• Pcb Single Layer: single side, 70 μm, CEM-1, 78x174 mm, Mixed PTH/SMT
• For Use With: 497-8834 - BOARD DEMO FOR L6563/LL6566A497-6452 - BOARD EVAL FOR L6566B497-6451 - BOARD EVAL FOR L6566B497-6450 - BOARD EVAL FOR L6566B497-6449 - BOARD EVAL FOR L6566A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Application information
5.12
38/51
Brownout protection
Brownout protection is basically a not-latched device shutdown function activated when a
condition of mains undervoltage is detected. There are several reasons why it may be
desirable to shut down a converter during a brownout condition, which occurs when the
mains voltage falls below the minimum specification of normal operation.
Firstly, a brownout condition may cause overheating of the PFC front-end due to an excess
of RMS current. Secondly, brownout can also cause the PFC pre-regulator to work open
loop. This could be dangerous to the PFC itself and the downstream converter, should the
input voltage return abruptly to its rated value, given the slow response of PFC to transient
events. Finally, spurious restarts may occur during converter power down, hence causing
the output voltage not to decay to zero monotonically.
L6566A shutdown upon brownout is accomplished by means of an internal comparator, as
shown in the block diagram of
input of the comparator, available on the AC_OK pin (16), is supposed to sense a voltage
proportional to either the RMS or the peak mains voltage; the non-inverting input is
internally referenced to 0.485 V with 35 mV hysteresis. If the voltage applied on the AC_OK
pin before the device starts operating does not exceed 0.485 V or if it falls below 0.45 V
while the device is running, The AC_OK signal goes high, the pin Vcc_PFC is open and the
device shuts down, with the soft-start capacitor discharged and the gate-drive output low.
Additionally, in case the device has been latched off by some protection function (in which
case Vcc is oscillating between V
0.45 V will clear the latch. This feature can be used to allow a quicker restart as the input
source is removed.
Figure 25. Brownout protection: internal block diagram and timing diagram
Sensed
R
R
voltage
H
L
AC_OK
16
L6566A
15 µA
0.485V
0.45V
Vcc
+
-
Figure 25
5
ccON
AC_FAIL
and V
, which shows the basic circuit usage. The inverting
ccON
Sensed voltage
Vsen
Vcc_PFC
VAC_OK
Vsen
(pin 16)
AC_FAIL
(pin 6)
- 0.5 V) the AC_OK voltage falling below
(pin 5)
(pin 4)
15 µA
Vcc
GD
Vout
OFF
I
HYS
ON
0.485V
L6566A
0.45V
t
t
t
t
t
t
t
t