BTS410E2 Infineon Technologies, BTS410E2 Datasheet - Page 7

• Manufacturer Part Number: BTS410E2
• Description: IC SWITCH PWR 65V TO-220AB-5
• Manufacturer: Infineon Technologies
• Series: PROFET®r
• Type: High Sider

Specifications of BTS410E2

• Input Type: Non-Inverting
• Number Of Outputs: 1
• On-state Resistance: 190 mOhm
• Current - Output / Channel: 1.8A
• Current - Peak Output: 12A
• Voltage - Supply: 4.7 V ~ 42 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Through Hole
• Package / Case: TO-220-5 (Bent and Staggered Leads)
• Device Type: High Side
• Peak Output Current: 1.8A
• Input Delay: 125µs
• Output Delay: 85µs
• Supply Voltage Range: 4.7V To 42V
• Driver Case Style: TO-220AB
• No. Of Pins: 5
• Operating Temperature Range: -40°C
• Switch Type: High Side
• Power Switch Family: BTS 410 E2
• Input Voltage: -0.5 to 6V
• Power Switch On Resistance: 190mOhm
• Output Current: 1.6A
• Mounting: Through Hole
• Supply Current: 1mA
• Package Type: TO-220AB
• Operating Temperature (min): -40C
• Operating Temperature (max): 150C
• Operating Temperature Classification: Automotive
• Pin Count: 5 +Tab
• Power Dissipation: 50W
• Rohs Compliant: No
• Output Resistance: 0.19ohm
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant, Contains lead / RoHS non-compliant
• Other names: BTS410E2; BTS410E2IN; BTS410E2NK; SP000011233

Status output
ESD-Zener diode: 6 V typ., max 5 mA;
R
to be used as voltage clamp at DC conditions.
Operation in this mode may result in a drift of the zener
voltage (increase of up to 1 V).
Short circuit detection
Fault Condition: V
Inductive and overvoltage output clamp
V
Semiconductor Group
ON
ST(ON)
clamped to 68 V typ.
Logic
unit
< 250
R
at 1.6 mA, ESD zener diodes are not
ON
ST(ON)
Short circuit
> 8.5 V typ.; IN high
detection
V
GND
Z
GND
PROFET
ESD-
ZD
ST
+5V
+ V bb
OUT
+ V bb
OUT
V
ON
V
ON
7
Overvolt. and reverse batt. protection
V
R
Open-load detection
ON-state diagnostic condition: V
high
GND disconnect
V
Any kind of load. In case of Input=high is V
Due to V
bb
Z1
ST
= 15 k
= 6.2 V typ., V
V
R
R
IN
GND
Logic
IN
ST
unit
V
>0, no V
ST
ST
IN
ON
2
4
V
ST
Z2
Z1
IN
ST
= low signal available.
Open load
detection
= 70 V typ., R
PROFET
Logic
GND
3
1
V
bb
R
V
GND
ON
GND
V
Z2
OUT
< R
OUT
GND
PROFET
BTS 410 E2
GND
ON
Signal GND
V
= 150 , R
2003-Oct-01
5
IN
* I
- V
+ V bb
L(OL)
OUT
V
IN(T+)
+ V bb
ON
; IN
.
IN
,