STEVAL-ISQ002V1 STMicroelectronics, STEVAL-ISQ002V1 Datasheet - Page 61
STEVAL-ISQ002V1
Manufacturer Part Number
STEVAL-ISQ002V1
Description
BOARD EVAL BASED ON ST72264G1
Manufacturer
STMicroelectronics
Specifications of STEVAL-ISQ002V1
Main Purpose
Interface, PMBus
Embedded
Yes, MCU, 8-Bit
Utilized Ic / Part
ST72F264
Primary Attributes
The PMBus™ Interface Using the ST7 I2C Peripheral
Secondary Attributes
Firmware in C Language
Product
Power Management Modules
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-6423
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STEVAL-ISQ002V1
Manufacturer:
STMicroelectronics
Quantity:
1
- Current page: 61 of 172
- Download datasheet (2Mb)
16-BIT TIMER (Cont’d)
11.3.3.4 Output Compare
In this section, the index, i, may be 1 or 2 because
there are 2 output compare functions in the 16-bit
timer.
This function can be used to control an output
waveform or indicate when a period of time has
elapsed.
When a match is found between the Output Com-
pare register and the free running counter, the out-
put compare function:
Two 16-bit registers Output Compare Register 1
(OC1R) and Output Compare Register 2 (OC2R)
contain the value to be compared to the counter
register each timer clock cycle.
These registers are readable and writable and are
not affected by the timer hardware. A reset event
changes the OC
Timing resolution is one count of the free running
counter: (
Procedure:
To use the output compare function, select the fol-
lowing in the CR2 register:
– Set the OCiE bit if an output is needed then the
– Select the timer clock (CC[1:0]) (see
And select the following in the CR1 register:
– Select the OLVLi bit to applied to the OCMPi pins
– Set the OCIE bit to generate an interrupt if it is
When a match is found between OCRi register
and CR register:
– OCFi bit is set.
OCMPi pin is dedicated to the output compare i
signal.
Clock Control
after the match occurs.
needed.
– Assigns pins with a programmable value if the
– Sets a flag in the status register
– Generates an interrupt if enabled
OCiR
OCIE bit is set
f
CPU/
CC[1:0]
Bits).
i
R value to 8000h.
MS Byte
OCiHR
).
LS Byte
OCiLR
Table 14
– The OCMPi pin takes OLVLi bit value (OCMPi
– A timer interrupt is generated if the OCIE bit is
The OC
ing application can be calculated using the follow-
ing formula:
Where:
∆
f
PRESC
If the timer clock is an external clock, the formula
is:
Where:
∆
f
Clearing the output compare interrupt request (i.e.
clearing the OCFi bit) is done by:
1. Reading the SR register while the OCFi bit is
2. An access (read or write) to the OCiLR register.
The following procedure is recommended to pre-
vent the OCFi bit from being set between the time
it is read and the write to the OC
– Write to the OCiHR register (further compares
– Read the SR register (first step of the clearance
– Write to the OCiLR register (enables the output
CPU
EXT
t
t
pin latch is forced low during reset).
set in the CR2 register and the I bit is cleared in
the CC register (CC).
are inhibited).
of the OCFi bit, which may be already set).
compare function and clears the OCFi bit).
set.
ST72260Gx, ST72262Gx, ST72264Gx
i
R register value required for a specific tim-
= Output compare period (in seconds)
= CPU clock frequency (in hertz)
= Timer prescaler factor (2, 4 or 8 de-
= Output compare period (in seconds)
= External timer clock frequency (in hertz)
pending on CC[1:0] bits, see
Clock Control
∆
∆
OCiR =
OCiR =
∆t
Bits)
∆t
*
PRESC
f
EXT
*
f
CPU
i
R register:
Table 14
61/172
Related parts for STEVAL-ISQ002V1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
BOARD RGB CTR ST7,STP08C596MTR
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Power Management IC Development Tools Full Speed USB to RS232 Bridge Demo
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Power Management IC Development Tools 2.5W solar eval BRD USB SPV1040 LD39050
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT DEV STARTER ST10F276Z5
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL HDMI $ VIDEO SWITCH
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD DEMO ACCELEROMETER DIL24
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD STLM75/STDS75/ST72F651
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EVAL BOARD 3AXIS MEMS ACCELLRMTR
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL 8BIT MICRO + TDE1708
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet: