Z8F083A0128ZCOG Zilog, Z8F083A0128ZCOG Datasheet - Page 80
Z8F083A0128ZCOG
Manufacturer Part Number
Z8F083A0128ZCOG
Description
KIT DEVELOPMENT F083A
Manufacturer
Zilog
Series
Z8 Encore! XP®r
Type
MCUr
Specifications of Z8F083A0128ZCOG
Contents
Hardware, Software and Documentation
For Use With/related Products
Z8F083A
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4672
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
Z8F083A0128ZCOG
Manufacturer:
Zilog
Quantity:
1
- Current page: 80 of 256
- Download datasheet (4Mb)
PS026308-1207
Caution:
2. Write to the timer high and low byte registers to set the starting count value (usually
3. Write to the timer reload high and low byte registers to set the reload value.
4. Enable the timer interrupt (if appropriate) and set the timer interrupt priority by
5. Configure the associated GPIO port pin (if using the timer output function) for the
6. Write to the timer control register to enable the timer and initiate counting.
In CONTINUOUS mode, the system clock always provides the timer input. The timer
period is given by the following equation:
If an initial starting value other than
registers, use the ONE-SHOT mode equation to determine the first time-out period.
COUNTER Mode
In COUNTER mode, the timer counts input transitions from a GPIO port pin. The timer
input is taken from the GPIO port pin: timer input alternate function. The TPOL bit in the
timer control register determines whether the count occurs on the rising edge or the falling
edge of the timer input signal. In COUNTER mode, the prescaler is disabled.
On reaching the reload value stored in the timer reload high and low byte registers, the
timer generates an interrupt, the count value in the timer high and low byte registers is
reset to
enabled, the timer output pin changes state (from low to high or from high to low) at timer
reload.
The steps for configuring a timer for COUNTER mode and for initiating the count are as
follows:
1. Write to the timer control register to:
Continuous Mode Time-Out Period (s)
The input frequency of the timer input signal must not exceed one-fourth the system
clock frequency.
–
0001H). This action only affects the first pass in CONTINUOUS mode. After the first
timer reload in CONTINUOUS mode, counting always begins at the reset value of
0001H
writing to the relevant interrupt registers.
timer output alternate function.
–
–
0001H
If using the timer output alternate function, set the initial output level (high or
low)
Disable the timer
Configure the timer for COUNTER mode
.
and counting resumes. Also, if the timer output alternate function is
0001H
=
is loaded into the timer high and low byte
--------------------------------------------------------------------------- -
System Clock Frequency (Hz)
Reload Value Prescale
Z8 Encore!
×
Product Specification
®
F083A Series
Timers
68
Related parts for Z8F083A0128ZCOG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: