PIC18LF6310-I/PT Microchip Technology, PIC18LF6310-I/PT Datasheet - Page 182

• Manufacturer Part Number: PIC18LF6310-I/PT
• Description: IC PIC MCU FLASH 4KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF6310-I/PT

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 54
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• No. Of Pwm: RoHS Compliant
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F6310/6410/8310/8410
17.3.5
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2,
broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be dis-
abled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
FIGURE 17-3:
DS39635C-page 182
Write to
SSPBUF
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
SDO
(CKE = 0)
SDO
(CKE = 1)
SDI
(SMP = 0)
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
Input
Sample
(SMP = 1)
SSPIF
SSPSR to
SSPBUF
MASTER MODE
SPI MODE WAVEFORM (MASTER MODE)
bit 7
bit 7
bit 7
bit 7
Figure
bit 6
bit 6
17-2) is to
bit 5
bit 5
bit 4
bit 4
bit 3
bit 3
The clock polarity is selected by appropriately
programming the CKP bit (SSPCON1<4>). This then,
would give waveforms for SPI communication as
shown in
where the MSB is transmitted first. In Master mode, the
SPI clock rate (bit rate) is user programmable to be one
of the following:
• F
• F
• F
• Timer2 output/2
Figure 17-3
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPBUF is loaded with the received
data is shown.
OSC
OSC
OSC
/4 (or T
/16 (or 4 • T
/64 (or 16 • T
bit 2
bit 2
Figure
shows the waveforms for Master mode.
CY
)
bit 1
bit 1
17-3,
CY
CY
)
)
 2010 Microchip Technology Inc.
Figure 17-5
bit 0
bit 0
bit 0
bit 0
Next Q4 Cycle
after Q2
and
4 Clock
Modes
Figure
17-6,