DSPIC33FJ128MC510-I/PT Microchip Technology, DSPIC33FJ128MC510-I/PT Datasheet - Page 22

• Manufacturer Part Number: DSPIC33FJ128MC510-I/PT
• Description: IC DSPIC MCU/DSP 128K 100TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128MC510-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 24x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 2.75V
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 85
• Flash Memory Size: 128KB
• Supply Voltage Range: 3V To 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1001 - DSPIC33 BREAKOUT BOARDAC164333 - MODULE SKT FOR PM3 100QFPMA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32DV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

58. Module: PWM
59. Module: PWM
60. Module: PWM
DS80447D-page 22
The PWM outputs, PWM2H and PWM2L, do not
generate PWM signals if the following two
conditions are met:
1. FLTBCON register is written with any value.
2. Fault pin B (FLTB) is low while the FLTBCON
Work around
There are three possible work arounds for this
issue:
1. Do not write to the FLTBCON register.
2. If Fault B is needed for the application, always
3. Set the FLTA pin to a logic low while writing to
Affected Silicon Revisions
If the PTDIR bit is set, when PTMR is counting
down, and the CPU execution is halted, after a
breakpoint is reached, PTMR will start counting up
as if PTDIR was zero.
Work around
None.
Affected Silicon Revisions
An active Fault while the Motor Control PWM
module is stopped in Idle mode does not result in
an interrupt request being sent to the processor.
Therefore, the processor does not wake-up from
Idle mode.
Work around
None.
Affected Silicon Revisions
A2
A2
A2
X
X
X
register is being written.
keep the FLTB pin connected to logic high
while writing to the FLTBCON register.
the FLTBCON register.
A3
A3
A3
X
X
X
A4
A4
A4
X
X
X
61. Module: PWM
When the device is operated in Doze mode and
the motor control PWM module has a postscaler
set to any value different than 1:1 (PTOPS > 0 in
PxTCON register), the motor control PWM module
generates more interrupts than expected.
Work around
Do not use Doze mode with the motor control
PWM if the time base output postscaler is different
than 1:1.
Affected Silicon Revisions
A2
X
A3
X
A4
X
© 2010 Microchip Technology Inc.