AT89S8253-24PU Atmel, AT89S8253-24PU Datasheet - Page 6

• Manufacturer Part Number: AT89S8253-24PU
• Description: IC 8051 MCU FLASH 12K 40DIP
• Manufacturer: Atmel
• Series: 89Sr

Specifications of AT89S8253-24PU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 32
• Program Memory Size: 12KB (12K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Cpu Family: 89S
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 24MHz
• Interface Type: SPI/UART
• Total Internal Ram Size: 256Byte
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89ISP
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

3.13
3.14
3.15
4. Block Diagram
6
EA/VPP
XTAL1
XTAL2
AT89S8253
External Access Enable. EA must be strapped to GND in order to enable the device to fetch
code from external program memory locations starting at 0000H up to FFFFH. Note, however,
that if lock bit 1 is programmed, EA will be internally latched on reset.
EA should be strapped to V
programming enable voltage (V
selected.
Input to the inverting oscillator amplifier and input to the internal clock operating circuit.
Output from the inverting oscillator amplifier. XTAL2 should not drive a board-level clock without
a buffer.
ALE/PROG
EA / V
PSEN
RST
V
GND
PP
CC
EEPROM
CONTROL
REGISTER
TIMING
AND
OSC
B
RAM ADDR.
REGISTER
INSTRUCTION
REGISTER
WATCH
DOG
CC
ACC
for internal program executions. This pin also receives the 12-volt
TMP2
PP
) during Flash programming when 12-volt programming is
RAM
PORT 3 DRIVERS
PSW
P3.0 - P3.7
PORT 0 DRIVERS
PORT 3
LATCH
ALU
P0.0 - P0.7
PORT 0
LATCH
TMP1
INTERRUPT, SERIAL PORT,
AND TIMER BLOCKS
PORT 2
LATCH
PORT 1 DRIVERS
PORT 1
LATCH
PORT 2 DRIVERS
POINTER
P2.0 - P2.7
STACK
P1.0 - P1.7
FLASH
PORT
SPI
INCREMENTER
PROGRAM
PROGRAM
REGISTER
PROGRAM
ADDRESS
COUNTER
LOGIC
BUFFER
DUAL
DPTR
PC
3286P–MICRO–3/10