AT89S8253-24PU Atmel, AT89S8253-24PU Datasheet - Page 8

• Manufacturer Part Number: AT89S8253-24PU
• Description: IC 8051 MCU FLASH 12K 40DIP
• Manufacturer: Atmel
• Series: 89Sr

Specifications of AT89S8253-24PU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 32
• Program Memory Size: 12KB (12K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Cpu Family: 89S
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 24MHz
• Interface Type: SPI/UART
• Total Internal Ram Size: 256Byte
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89ISP
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

5.1
Table 5-2.
5.2
Table 5-3.
5.3
5.4
8
AUXR Address = 8EH
Not Bit Addressable
Bit
Symbol
Intel_Pwd_Exit
DISALE
CLKREG Address = 8FH
Not Bit Addressable
Bit
Symbol
X2
Auxiliary Register
Clock Register
SPI Registers
Interrupt Registers
AT89S8253
–
7
–
7
Function
When X2 = 0, the oscillator frequency (at XTAL1 pin) is internally divided by 2 before it is used as the device system
frequency.
When X2 = 1, the divider by 2 is no longer used and the XTAL1 frequency becomes the device system frequency. This
enables the user to choose a 6 MHz crystal instead of a 12 MHz crystal, for example, in order to reduce EMI.
AUXR – Auxiliary Register
CLKREG – Clock Register
Function
When set, this bit configures the interrupt driven exit from power-down to resume execution on the rising edge of
the interrupt signal. When this bit is cleared, the execution resumes after a self-timed interval (nominal 2 ms)
referenced from the falling edge of the interrupt signal.
When DISALE = 0, ALE is emitted at a constant rate of 1/6 the oscillator frequency (except during MOVX when 1
ALE pulse is missing). When DISALE = 1, ALE is active only during a MOVX or MOVC instruction.
–
6
–
6
Control and status bits for the Serial Peripheral Interface are contained in registers SPCR (see
Table 14-1 on page
in the SPDR register. In normal SPI mode, writing the SPI data register during serial data trans-
fer sets the Write Collision bit (WCOL) in the SPSR register. In enhanced SPI mode, the SPDR
is also write double-buffered because WCOL works as a Write Buffer Full Flag instead of being a
collision flag. The values in SPDR are not changed by Reset.
The global interrupt enable bit and the individual interrupt enable bits are in the IE register. In
addition, the individual interrupt enable bit for the SPI is in the SPCR register. Four priorities can
be set for each of the six interrupt sources in the IP and IPH registers.
IPH bits have the same functions as IP bits, except IPH has higher priority than IP. By using IPH
in conjunction with IP, a priority level of 0, 1, 2, or 3 may be set for each interrupt.
–
5
–
5
25) and SPSR (see
–
4
–
4
–
3
Table 14-2 on page
–
3
–
2
–
2
26). The SPI data bits are contained
Intel_Pwd_Exit
Reset Value = XXXX XXX0B
Reset Value = XXXX XXX0B
1
–
1
DISALE
3286P–MICRO–3/10
X2
0
0