PIC18F26J50-I/SP Microchip Technology, PIC18F26J50-I/SP Datasheet - Page 52

• Manufacturer Part Number: PIC18F26J50-I/SP
• Description: IC PIC MCU FLASH 64K 2V 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26J50-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 16
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART/I2C/SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DV164136, MA180024, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2XK20/4XK20
REGISTER 4-1:
DS41303D-page 50
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
Note 1: Brown-out Reset is indicated when BOR is ‘0’ and POR is ‘1’ (assuming that both POR and BOR were set
R/W-0
IPEN
2:
3:
2: It is recommended that the POR bit be set after a Power-on Reset has been detected so that subsequent
When CONFIG2L[2:1] = 01, then the SBOREN Reset state is ‘1’; otherwise, it is ‘0’.
The actual Reset value of POR is determined by the type of device Reset. See the notes following this
register and Section 4.6 “Reset State of Registers” for additional information.
See Table 4-3.
to ‘1’ by firmware immediately after POR).
Power-on Resets may be detected.
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
SBOREN: BOR Software Enable bit
If BOREN<1:0> = 01:
1 = BOR is enabled
0 = BOR is disabled
If BOREN<1:0> = 00, 10 or 11:
Bit is disabled and read as ‘0’.
Unimplemented: Read as ‘0’
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware or Power-on Reset)
0 = The RESET instruction was executed causing a device Reset (must be set in firmware after a
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
POR: Power-on Reset Status bit
1 = No Power-on Reset occurred
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set by firmware after a POR or Brown-out Reset occurs)
SBOREN
R/W-1
code-executed Reset occurs)
RCON: RESET CONTROL REGISTER
(1)
W = Writable bit
‘1’ = Bit is set
U-0
—
R/W-1
(2)
(3)
Preliminary
RI
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-1
TO
R-1
PD
© 2008 Microchip Technology Inc.
x = Bit is unknown
POR
R/W-0
(2)
R/W-0
BOR
bit 0