ATMEGA640-16CU Atmel, ATMEGA640-16CU Datasheet - Page 45

• Manufacturer Part Number: ATMEGA640-16CU
• Description: IC MCU AVR 64K FLASH 100-CBGA
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA640-16CU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.6
2549M–AVR–09/10
Low Frequency Crystal Oscillator
Table 9-6.
Notes:
The device can utilize a 32.768 kHz watch crystal as clock source by a dedicated Low Fre-
quency Crystal Oscillator. The crystal should be connected as shown in
When this Oscillator is selected, start-up times are determined by the SUT Fuses and CKSEL0
as shown in
The Low-Frequency Crystal Oscillator provides an internal load capacitance, see
each XTAL/TOSC pin.
Table 9-7.
Device
Ceramic resonator, slowly
Ceramic resonator, slowly
ATmega640/1280/1281/2560
Ceramic resonator, BOD
Crystal Oscillator, slowly
Ceramic resonator, fast
Ceramic resonator, fast
Crystal Oscillator, BOD
Crystal Oscillator, fast
Oscillator Source /
Power Conditions
rising power
rising power
rising power
rising power
rising power
rising power
1. These options should only be used when not operating close to the maximum frequency of the
2. These options are intended for use with ceramic resonators and will ensure frequency stability
enabled
enabled
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals.
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
/2561
Table 9-8 on page
Start-up Times for the Full Swing Crystal Oscillator Clock Selection
Capacitance for Low Frequency Oscillator
32 kHz oscillator
Start-up Time from
Power-down and
46.
ATmega640/1280/1281/2560/2561
Power-save
System Osc.
Timer Osc.
16K CK
16K CK
16K CK
258 CK
258 CK
1K CK
1K CK
1K CK
Cap (Xtal1/Tosc1)
Additional Delay
14CK + 4.1 ms
14CK + 4.1 ms
14CK + 65 ms
14CK + 65 ms
14CK + 4.1 ms
14CK + 65 ms
(V
from Reset
CC
14CK
14CK
18 pF
6 pF
= 5.0V)
(2)
(1)
(2)
(1)
(2)
Figure 9-2 on page
Cap (Xtal2/Tosc2)
CKSEL0
0
0
0
0
1
1
1
1
8 pF
6 pF
Table 9-7
SUT1:0
00
01
10
11
00
01
10
11
43.
45
at