ATMEGA640-16CU Atmel, ATMEGA640-16CU Datasheet - Page 70

• Manufacturer Part Number: ATMEGA640-16CU
• Description: IC MCU AVR 64K FLASH 100-CBGA
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA640-16CU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12. I/O-Ports
12.1
2549M–AVR–09/10
Introduction
All AVR ports have true Read-Modify-Write functionality when used as general digital I/O ports.
This means that the direction of one port pin can be changed without unintentionally changing
the direction of any other pin with the SBI and CBI instructions. The same applies when chang-
ing drive value (if configured as output) or enabling/disabling of pull-up resistors (if configured as
input). Each output buffer has symmetrical drive characteristics with both high sink and source
capability. The pin driver is strong enough to drive LED displays directly. All port pins have indi-
vidually selectable pull-up resistors with a supply-voltage invariant resistance. All I/O pins have
protection diodes to both V
acteristics” on page 367
Figure 12-1. I/O Pin Equivalent Schematic
All registers and bit references in this section are written in general form. A lower case “x” repre-
sents the numbering letter for the port, and a lower case “n” represents the bit number. However,
when using the register or bit defines in a program, the precise form must be used. For example,
PORTB3 for bit no. 3 in Port B, here documented generally as PORTxn. The physical I/O Regis-
ters and bit locations are listed in
Port L to the overriding signals shown in Figure 12-5 on page 76.” on page
Three I/O memory address locations are allocated for each port, one each for the Data Register
– PORTx, Data Direction Register – DDRx, and the Port Input Pins – PINx. The Port Input Pins
I/O location is read only, while the Data Register and the Data Direction Register are read/write.
However, writing a logic one to a bit in the PINx Register, will result in a toggle in the correspond-
ing bit in the Data Register. In addition, the Pull-up Disable – PUD bit in MCUCR disables the
pull-up function for all pins in all ports when set.
Using the I/O port as General Digital I/O is described in
71. Most port pins are multiplexed with alternate functions for the peripheral features on the
device. How each alternate function interferes with the port pin is described in
Functions” on page
nate functions.
Pxn
75. Refer to the individual module sections for a full description of the alter-
for a complete list of parameters.
CC
and Ground as indicated in
ATmega640/1280/1281/2560/2561
“Table 12-34 and Table 12-35 relates the alternate functions of
C
pin
“Ports as General Digital I/O” on page
Figure
"General Digital I/O" for
12-1. Refer to
See Figure
R
Details
pu
Logic
99.
“Electrical Char-
“Alternate Port
70