MC908QY2AMDTE Freescale Semiconductor, MC908QY2AMDTE Datasheet - Page 42

• Manufacturer Part Number: MC908QY2AMDTE
• Description: IC MCU 8BIT 1.5K FLASH 16TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QY2AMDTE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 1.5KB (1.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-TSSOP
• Processor Series: HC08QY
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Analog-to-Digital Converter (ADC10) Module
3.3.4 Sources of Error
Several sources of error exist for ADC conversions. These are discussed in the following sections.
3.3.4.1 Sampling Error
For proper conversions, the input must be sampled long enough to achieve the proper accuracy. Given
the maximum input resistance of approximately 15 kΩ and input capacitance of approximately 10 pF,
sampling to within
1/4
maximum ADCK frequency) provided the resistance of the external analog source (R
kΩ. Higher source resistances or higher-accuracy sampling is possible by setting ADLSMP (to increase
the sample window to 23.5 cycles) or decreasing ADCK frequency to increase sample time.
3.3.4.2 Pin Leakage Error
Leakage on the I/O pins can cause conversion error if the external analog source resistance (R
If this error cannot be tolerated by the application, keep R
1/4
3.3.4.3 Noise-Induced Errors
System noise which occurs during the sample or conversion process can affect the accuracy of the
conversion. The ADC10 accuracy numbers are guaranteed as specified only if the following conditions
are met:
There are some situations where external system activity causes radiated or conducted noise emissions
or excessive V
in wait or I/O activity cannot be halted, the following recommendations may reduce the effect of noise on
the accuracy:
42
•
•
•
•
•
•
•
•
•
•
LSB
LSB
There is a 0.1μF low-ESR capacitor from V
There is a 0.1μF low-ESR capacitor from V
If inductive isolation is used from the primary supply, an additional 1μF capacitor is placed from
V
V
The MCU is placed in wait mode immediately after initiating the conversion (next instruction after
write to ADSCR).
There is no I/O switching, input or output, on the MCU during the conversion.
Place a 0.01 μF capacitor on the selected input channel to V
improve noise issues but will affect sample rate based on the external analog source resistance.
Operate the ADC10 in stop mode by setting ACLKEN, selecting the channel in ADSCR, and
executing a STOP instruction. This will reduce V
due to stop recovery.
Average the input by converting the output many times in succession and dividing the sum of the
results. Four samples are required to eliminate the effect of a 1
Reduce the effect of synchronous noise by operating off the asynchronous clock (ACLKEN=1) and
averaging. Noise that is synchronous to the ADCK cannot be averaged out.
(at 10-bit resolution) can be achieved within the minimum sample window (3.5 cycles / 2 MHz
leakage error (at 10-bit resolution).
DDA
SSA
and V
to V
DD
SSA
noise is coupled into the ADC10. In these cases, or when the MCU cannot be placed
REFL
(if available).
(if available) is connected to V
MC68HC908QYA/QTA Family Data Sheet, Rev. 3
REFH
DDA
SS
DD
to V
to V
AS
at a quiet point in the ground plane.
noise but will increase effective conversion time
SSA
lower than V
REFL
(if available).
(if available).
REFL
LSB
ADVIN
or V
, one-time error.
SSA
/ (4096*I
(if available). This will
Freescale Semiconductor
AS
Leak
) is kept below 10
) for less than
AS
) is high.