MC9S12XET256CAG Freescale Semiconductor, MC9S12XET256CAG Datasheet - Page 1166

• Manufacturer Part Number: MC9S12XET256CAG
• Description: MCU 16BIT 256K FLASH 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XET256CAG

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 50MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 119
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: S12XE
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: KIT33812ECUEVME, EVB9S12XEP100, DEMO9S12XEP100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 29 1024 KByte Flash Module (S12XFTM1024K5V2)
29.3.2.9.1
The general guideline is that P-Flash protection can only be added and not removed.
all valid transitions between P-Flash protection scenarios. Any attempt to write an invalid scenario to the
FPROT register will be ignored. The contents of the FPROT register reflect the active protection scenario.
See the FPHS and FPLS bit descriptions for additional restrictions.
29.3.2.10 EEE Protection Register (EPROT)
The EPROT register defines which buffer RAM EEE partition areas are protected against writes.
All bits in the EPROT register are readable and writable except for RNV[6:4] which are only readable. The
EPOPEN and EPDIS bits can only be written to the protected state. The EPS bits can be written anytime
until the EPDIS bit is cleared. If the EPOPEN bit is cleared, the state of the EPDIS and EPS bits is
irrelevant.
During the reset sequence, the EPROT register is loaded from the EEE protection byte in the Flash
configuration field at global address 0x7F_FF0D located in P-Flash memory (see
by reset condition F in
sequence, the P-Flash sector containing the EEE protection byte must be unprotected, then the EEE
protection byte must be programmed. If a double bit fault is detected while reading the P-Flash phrase
1166
Offset Module Base + 0x0009
Reset
W
R
EPOPEN
F
7
P-Flash Protection Restrictions
1. Allowed transitions marked with X, see
Protection
Scenario
From
= Unimplemented or Reserved
0
1
2
3
4
5
6
7
Figure
F
6
Table 29-23. P-Flash Protection Scenario Transitions
Figure 29-15. EEE Protection Register (EPROT)
29-15. To change the EEE protection that will be loaded during the reset
MC9S12XE-Family Reference Manual , Rev. 1.23
X
X
0
RNV[6:4]
F
5
X
X
X
X
1
X
X
X
X
2
To Protection Scenario
F
4
Figure 29-14
X
X
X
X
X
X
X
X
3
EPDIS
X
X
X
X
4
for a definition of the scenarios.
F
3
(1)
5
X
X
F
2
X
X
6
Table
Table 29-23
EPS[2:0]
Freescale Semiconductor
X
7
F
1
29-3) as indicated
specifies
F
0