ATMEGA103L-4AC Atmel, ATMEGA103L-4AC Datasheet - Page 107
ATMEGA103L-4AC
Manufacturer Part Number
ATMEGA103L-4AC
Description
IC MCU 128K 4MHZ A/D LV 64TQFP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheets
1.ATMEGA103-6AC.pdf
(141 pages)
2.ATMEGA103-6AC.pdf
(4 pages)
3.ATMEGA103L-4AC.pdf
(4 pages)
Specifications of ATMEGA103L-4AC
Core Processor
AVR
Core Size
8-Bit
Speed
4MHz
Connectivity
SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
32
Program Memory Size
128KB (64K x 16)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
64-TQFP, 64-VQFP
For Use With
ATSTK501 - ADAPTER KIT FOR 64PIN AVR MCU
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 107 of 141
- Download datasheet (3Mb)
Enter Programming Mode
Chip Erase
Programming the Flash
0945I–AVR–02/07
The following algorithm puts the device in Parallel Programming mode:
1. Apply supply voltage according to Table 36, between V
2. Set RESET and BS1 pins to “0” and wait at least 100 ns.
3. Apply 11.5 - 12.5V to RESET. Any activity on BS1 within 100 ns after +12V has
The Chip Erase will erase the Flash and EEPROM memories, and Lock bits. The Lock
bits are not reset until the Program memory has been completely erased. The Fuse bits
are not changed. A chip erase must be performed before the Flash or EEPROM is
reprogrammed.
Load Command “Chip Erase”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “1000 0000”. This is the command for Chip Erase.
4. Give XTAL1 a positive pulse. This loads the command.
5. Give WR a
Table 40. Minimum WR Pulse Width for Chip Erase
The Flash is organized as 512 pages of 256 bytes each. When programming the Flash,
the program data is latched into a page buffer. This allows one page of program data to
be programmed simultaneously. The following procedure describes how to program the
entire Flash memory:
A: Load Command “Write Flash”.
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “0001 0000”. This is the command for Write Flash.
4. Give XTAL1 a positive pulse. This loads the command.
B: Load Address Low Byte.
1. Set XA1, XA0 to “00”. This enables address loading.
2. Set BS1 to “0”. This selects low address.
3. Set DATA = Address Low Byte ($00 - $FF)
4. Give XTAL1 a positive pulse. This loads the address Low Byte.
C: Load Data Low Byte.
1. Set BS1 to “0”. This selects low data.
2. Set XA1, XA0 to “01”. This enables data loading.
3. Set DATA = Data Low Byte ($00 - $FF).
4. Give XTAL1 a positive pulse. This loads the data byte.
D: Latch Data Low Byte.
1. Give PAGEL a positive pulse. This latches the data Low Byte.
(See Figure 73 for signal waveforms.)
Symbol
t
WLWH_CE
been applied to RESET will cause the device to fail entering Programming mode.
t
WLWH_CE
value. Chip Erase does not generate any activity on the RDY/BSY pin.
t
WLWH_CE
wide negative pulse to execute Chip Erase. See Table 40 for
56 ms
3.2V
43 ms
3.6V
CC
ATmega103(L)
35 ms
4.0V
and GND.
22 ms
5.0V
107
Related parts for ATMEGA103L-4AC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC MCU 128K 6MHZ A/D 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU 128K 6MHZ A/D IT 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Atmega103 8-bit With 128k Bytes Of In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1280/AT86RF230 100TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA1280/AT86RF100-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA2560V/AT86RF230-ZU
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA2561/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika