ATMEGA103L-4AC Atmel, ATMEGA103L-4AC Datasheet - Page 84
ATMEGA103L-4AC
Manufacturer Part Number
ATMEGA103L-4AC
Description
IC MCU 128K 4MHZ A/D LV 64TQFP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheets
1.ATMEGA103-6AC.pdf
(141 pages)
2.ATMEGA103-6AC.pdf
(4 pages)
3.ATMEGA103L-4AC.pdf
(4 pages)
Specifications of ATMEGA103L-4AC
Core Processor
AVR
Core Size
8-Bit
Speed
4MHz
Connectivity
SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
32
Program Memory Size
128KB (64K x 16)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
64-TQFP, 64-VQFP
For Use With
ATSTK501 - ADAPTER KIT FOR 64PIN AVR MCU
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 84 of 141
- Download datasheet (3Mb)
Interface to External
SRAM
84
ATmega103(L)
The interface to the SRAM consists of:
Port A: multiplexed low-order address bus and data bus
Port C: high-order address bus
The ALE pin: address latch enable
The RD and WR pin: read and write strobes
The external data SRAM is enabled by setting the external SRAM enable bit (SRE) of
the MCU Control Register (MCUCR) and will override the setting of the Data Direction
Register (DDRA). When the SRE bit is cleared (zero), the external data SRAM is dis-
abled and the normal pin and data direction settings are used. When SRE is cleared
(zero), the address space above the internal SRAM boundary is not mapped into the
internal SRAM as AVR parts do not have an interface to the external SRAM.
When ALE goes from high to low, there is a valid address on Port A. ALE is low during a
data transfer. RD and WR are active when accessing the external SRAM only.
When the external SRAM is enabled, the ALE signal may have short pulses when
accessing the internal RAM, but the ALE signal is stable when accessing the external
SRAM.
Figure 50 shows how to connect an external SRAM to the AVR using eight latches that
are transparent when G is high.
By default, the external SRAM access is a three-cycle scheme as depicted in Figure 51.
When one extra wait state is needed in the access cycle, set the SRW bit (one) in the
MCUCR Register. The resulting access scheme is shown in Figure 52. In both cases,
note that Port A is data bus in one cycle only. As soon as the data access finishes, Port
A becomes a low-order address bus again.
Note:
For details on the timing for the SRAM interface, please refer to Figure 79, Table 45,
Table 46, Table 47, and Table 48 in the section “DC Characteristics” on page 118 and
refer to “Architectural Overview” on page 8 for a description of the memory map, includ-
ing address space for SRAM.
Figure 50. External SRAM Connected to the AVR
If a read is followed by a write, or vice versa, there is no extra insertion of wait states in
between. The user may insert a NOP between consecutive read and write operations to
the external RAM, because such short time for releasing the bus is difficult to obtain with-
out making bus contention.
AVR
Port C
Port A
ALE
WR
RD
D
G
Q
D[7:0]
A[15:8]
A[7:0]
RD
WR
SRAM
0945I–AVR–02/07
Related parts for ATMEGA103L-4AC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC MCU 128K 6MHZ A/D 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU 128K 6MHZ A/D IT 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Atmega103 8-bit With 128k Bytes Of In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1280/AT86RF230 100TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA1280/AT86RF100-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA2560V/AT86RF230-ZU
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA2561/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika