ATMEGA88PV-10AU Atmel, ATMEGA88PV-10AU Datasheet - Page 85

• Manufacturer Part Number: ATMEGA88PV-10AU
• Description: MCU AVR 8K ISP FLSH 10MHZ 32TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA88PV-10AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, TWI, UART
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 32TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 10 MHz
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 10MHz
• Rohs Compliant: Yes
• For Use With: ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8025L–AVR–7/10
• ADC1/PCINT9 – Port C, Bit 1
PC1 can also be used as ADC input Channel 1. Note that ADC input channel 1 uses analog
power.
PCINT9: Pin Change Interrupt source 9. The PC1 pin can serve as an external interrupt source.
• ADC0/PCINT8 – Port C, Bit 0
PC0 can also be used as ADC input Channel 0. Note that ADC input channel 0 uses analog
power.
PCINT8: Pin Change Interrupt source 8. The PC0 pin can serve as an external interrupt source.
Table 13-7
shown in
Table 13-7.
Note:
Signal
Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
DIEOE
DIEOV
DI
AIO
1. When enabled, the 2-wire Serial Interface enables slew-rate controls on the output pins PC4
Figure 13-5 on page
PC6/RESET/PCINT14
RSTDISBL
1
RSTDISBL
0
0
0
RSTDISBL + PCINT14 •
PCIE1
RSTDISBL
PCINT14 INPUT
RESET INPUT
and PC5. This is not shown in the figure. In addition, spike filters are connected between the
AIO outputs shown in the port figure and the digital logic of the TWI module.
and
Overriding Signals for Alternate Functions in PC6..PC4
Table 13-8
relate the alternate functions of Port C to the overriding signals
78.
PC5/SCL/ADC5/PCINT13
TWEN
PORTC5 • PUD
TWEN
SCL_OUT
TWEN
0
PCINT13 • PCIE1 + ADC5D
PCINT13 • PCIE1
PCINT13 INPUT
ADC5 INPUT / SCL INPUT
ATmega48P/88P/168P
PC4/SDA/ADC4/PCINT12
TWEN
PORTC4 • PUD
TWEN
SDA_OUT
TWEN
0
PCINT12 • PCIE1 + ADC4D
PCINT12 • PCIE1
PCINT12 INPUT
ADC4 INPUT / SDA INPUT
(1)
85