BLM18AG151SH1D Murata, BLM18AG151SH1D Datasheet - Page 15

• Manufacturer Part Number: BLM18AG151SH1D
• Description: EMI/RFI Suppressors & Ferrites 0603 150ohms Gen Use Tape
• Manufacturer: Murata
• Series: BLM Ar

Specifications of BLM18AG151SH1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 150 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.25 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0603 (1608 metric)
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1
!Note
!Note
<Unless otherwise specified>
1. Electrical Performance
2. Mechanical Performance
14
No.
No.
Specifications and Test Methods
1
2
1
2
3
4
5
6
Test and Measurement Conditions
Temperature: Ordinary Temp. 15 to 35 C
Humidity: Ordinary Humidity 25 to 85%(RH)
Specifications
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
Impedance
DC Resistance
Appearance and
Dimensions
Solderability
Resistance to Soldering
Heat
Bonding Strength
Bending Strength
Vibration
Item
Item
Meet rating table above
Impedance frequency
Characteristics (Typical): see the appendix.
Meet rating table above.
Meet dimensions.
The electrodes should be at least 95% covered with
new solder coating.
Meet Table 1.
Specifications
Specifications
<In case of doubt>
Temperature: 20 2 C
Humidity: 60 to 70%(RH)
Atmospheric pressure: 86 to 106kPa
Measuring Equipment: Agilent 4291A or the equivalent
Measuring Frequency: 100 1MHz
Test Fixture: Agilent 16092A or the equivalent
(for BLM18BApppSH1p type: Agilent 16192A
or the equivalent)
Measuring Equipment: Digital multi-meter
Visual Inspection and measured with Slide Calipers.
Flux: Ethanol solution of rosin, 25wt%
Pre-heating: 150 5 C, 60 5s
Solder: (1) Sn/Pb=60/40
Solder Temperature: (1) 230 5 C
Immersion Time: (1) 4 1s
Immersion and emersion rates: 25mm/s
Flux: Ethanol solution of rosin, 25wt%
Pre-heating: 150 5 C, 60 5s
Solder: Sn/Pb=60/40 or Sn-3.0Ag-0.5Cu solder
Solder Temperature: 270 5 C
Immersion Time: 10 0.5s
Immersion and emersion rates: 25mm/s
Then measured after exposure to room conditions for 48 4 hrs.
It should be soldered on the substrate.
Applying Force (F): 6.8N
Applying Time: 5 1s
It should be soldered on the glass-epoxy substrate.
Subatrate: 100 x 40 x 1.6mm
Deflection (n): 1.0mm (Glass-epoxy substrate)
Speed of Applying Force: 0.5mm/s
Keeping Time: 30s
It should be soldered on the substrate.
Oscillation Frequency: 10 to 2000 to 10Hz for 20 min.
Total Amplitude: 1.5mm or Acceleration amplitude 49m/s
whichever is smaller.
Testing Time: A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hrs.)
(2) Sn-3.0Ag-0.5Cu solder
(2) 3 1s
(2) 240 5 C
45mm
Test Methods
Test Methods
R340 F
R0.5
45mm
Pressure jig
F
Product
Deflection
C50E.pdf 05.1.28
Substrate
(Side view)
2
F
1