BLM18AG151SH1D Murata, BLM18AG151SH1D Datasheet - Page 22

• Manufacturer Part Number: BLM18AG151SH1D
• Description: EMI/RFI Suppressors & Ferrites 0603 150ohms Gen Use Tape
• Manufacturer: Murata
• Series: BLM Ar

Specifications of BLM18AG151SH1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 150 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.25 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0603 (1608 metric)
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
!Note
<Unless otherwise specified>
1. Electrical Performance
2. Mechanical Performance
No.
No.
1
2
3
4
1
2
3
4
5
Test and Measurement Conditions
Temperature: Ordinary Temp. 15 to 35 C
Humidity: Ordinary Humidity 25 to 85%(RH)
Specifications
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
Capacitance (Cap.)
Insulation Resistance
(I.R.)
Withstanding Voltage
Resistance to
Surge Voltage
Appearance and
Dimensions
Solderability
Resistance to
soldering heat
Bending Strength
Vibration
Item
Item
Meet rating table above.
Meet rating table above.
Products should not be damaged.
Meet Table 2.
Table 2
Meet dimensions.
The electrodes should be at least 75% covered with
new solder coating.
Meet Table 2.
Meet Table 3.
Table 3
Meet Table 2.
Withstanding
Cap. Change
Cap. Change
Appearance
Appearance
Voltage
I.R.
33, 68, 100, 180,
33, 68, 100, 180,
1000, 3300 (pF)
1000, 3300 (pF)
360, 680 (pF)
360, 680 (pF)
Specifications
Specifications
Meet rating table above.
No damage
No damage
No damage
within 15%
within 30%
within 15%
within 30%
<In case of doubt>
Temperature: 20 2 C
Humidity: 60 to 70%(RH)
Atmospheric pressure: 86 to 106kPa
Specifications and Test Methods
Table 1
Voltage: 100Vdc
Charging Time: 60 5s
Test Voltage: 250Vdc
Testing Time: 1 to 5s
Charge/Discharge current: 10mA max.
Attenuating transient voltage of exponential function should be
applied to products in the following conditions:
Peak Voltage: 400V
Force Period: 1s
The number of Surges: 10
Visual Inspection and measured with Slide Calipers
Flux: Ethanol solution of rosin, 25wt%
Pre-heat: 150 5 C, 60 5s
Solder: (1) Sn/Pb = 60/40
Solder Temperature: (1) 230 5 C
Immersion Time: (1) 4 1s
Immersion and emersion rates: 25mm/s
Flux: Ethanol solution of rosin, 25wt%
Pre-heat: 150 5 C, 60 5s
Solder: Sn/Pb = 60/40 or Sn-3.0Ag-0.5Cu solder
Solder Temperature: 270 5 C
Immersion Time: 10 1s
Immersion and emersion rates: 25mm/s
It should be soldered on the paper-phenol substrate. (t=1.6mm)
Deflection: 3mm
Keeping Time: 30s
Oscillation Frequency: 10 to 2000 to 10Hz for 20 min.
Total Amplitude: 1.5mm or Acceleration amplitude 49m/s
whichever is smaller
Testing Time: A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hrs.)
180, 360, 680, 1000, 3300 (pF)
(2) Sn-3.0Ag-0.5Cu solder
33, 68, 100 (pF)
Capacitance
(2) 3 1s
E
B
(for NFE61HT332Z2A9p: 250 5 C)
(2) 240 3 C
Test Methods
0.47 F
Test Methods
45
5
R340 F
Relay
Pressure jig
45
100
1 to 5Vrms
1 0.2Vrms
Voltage
10
Product
E
Deflection
B
Filter
1
2 3
400V
(in mm)
C50E.pdf 05.1.28
1MHz 10%
Frequency
1kHz 10%
2
21
1
2