BLM18AG151SH1D Murata, BLM18AG151SH1D Datasheet - Page 26

• Manufacturer Part Number: BLM18AG151SH1D
• Description: EMI/RFI Suppressors & Ferrites 0603 150ohms Gen Use Tape
• Manufacturer: Murata
• Series: BLM Ar

Specifications of BLM18AG151SH1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 150 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.25 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0603 (1608 metric)
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
!Note
<Unless otherwise specified>
1. Electrical Performance
2. Mechanical Performance
No.
No.
1
2
3
4
1
2
3
4
5
Test and Measurement Conditions
Temperature: Ordinary Temp. 15 to 35 C
Humidity: Ordinary Humidity 25 to 85%(RH)
Specifications
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
Common Mode
Impedance (Zc)
Insulation
Resistance (I.R.)
Withstanding Voltage
DC Resistance (Rdc)
Appearance
and Dimensions
Solderability
Resistance to
Soldering Heat
Bonding Strength
Bending Strength
Item
Item
Meet rating table above.
Products should not be damaged.
Meet rating table above.
Meet dimensions.
The electrodes should be at least 90% covered with
new solder coating.
Meet Table 1.
No evidence of coming off substrate.
Products should not be mechanically damaged.
Meet Table 1.
Specifications
Specifications
<In case of doubt>
Temperature: 20 2 C
Humidity: 60 to 70%(RH)
Atmospheric Pressure: 86 to 106kPa
Specifications and Test Methods
Measuring Equipment: Agilent 4291A or the equivalent
Measuring Frequency:100 1MHz
Test Fixture: Agilent 16092A or equivalent
Measuring voltage: Rated Voltage
Charging time: 1 minute max.
Test Voltage: 2.5 times for Rated Voltage
Tsting Time: 1 to 5s
Charge/Discharge Current: 1mA max.
Measuring current: 10mA max.
(In case of doubt in the above mentioned standard condition,
measure by four terminal methods.)
Visual Inspection and measured with Slide Calipers
The electrodes should be at least 90% covered with new solder
coating.
Flux: Ethanol solution of rosin, 25wt% includes activator
equivalent to 0.06 to 0.10wt% chlorine
Pre-heating: 150 5 C, 60 5s
Solder: (1) Sn/Pb=60/40
Solder Temperature: (1) 230 5 C
Immersion Time: (1) 3 0.5s
Immersion and emersion rates: 25mm/s
Flux: Ethanol solution of rosin, 25wt% includes activator
equipment to 0.06 to 0.10wt% chlorine
Pre-heating: 150 5 C, 60 5s
Solder: Sn/Pb=60/40 or Sn-3.0Ag-0.5Cu solder
Solder Temperature: 260 5 C
Immersion Time: 10 0.5s
Immersion and emersion rates: 25mm/s
Then measured after exposure in the room condition for 4 to
48 hrs.
It should be soldered on the substrate.
Applying Force (F): 10N
Applying Time: 5 1s
It should be soldered on the Glass-epoxy substrate (t=1.0mm).
Deflection (n): 2.0mm
Keeping time: 5s
Speed of Applying Force: 0.5mm/s
(2) Sn-3.0Ag-0.5Cu solder
(2) 4 1s
Substrate
Stainless tweezers
(2) 245 3 C
45
Test Methods
Test Methods
R230 F
Pressure jig
45
Continued on the following page.
Test board fixture
Pressure
Product
Product
Please hold except
this part.
Deflection
C50E.pdf 05.1.28
(in mm)
25
1
3