HP75BNC12X Switchcraft Inc., HP75BNC12X Datasheet - Page 149

• Manufacturer Part Number: HP75BNC12X
• Description: CONN BNC PLUG TRUE 75 OHM CRIMP
• Manufacturer: Switchcraft Inc.
• Series: BNCr
• Type: BNCr

Specifications of HP75BNC12X

• Impedance: 75 Ohm
• Rohs Information: Switchcraft RoHS Info.
• Connector Style: BNC
• Connector Type: Plug, Male Pins
• Contact Termination: Crimp
• Mounting Type: Free Hanging (In-Line)
• Fastening Type: Bayonet Lock
• Gender: M
• Body Style: Straight
• Terminate To: Coaxial Cable
• Mounting Style: Cable
• Termination: Crimp
• Body Plating: Nickel
• Contact Plating: Gold
• Contact Material: Copper Alloy
• Body Material: Copper Alloy
• Product Length (mm): 25mm
• Product: Connector
• Rf Series: BNC
• Polarity: Normal
• Shell Plating: Nickel
• Termination Style: Crimp
• Cable Type: Belden 1417B, 1855A, 1865A, Gepco VDM230, VDM250, RGB230/250 Series, Comm/Scope 7537, 7538
• Housing Material: Copper Alloy
• Maximum Frequency: 3 GHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Frequency-max: -
• Color: -
• Cable Group: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

144
w w w . s w i t c h c r a f t . c o m
JACKS AND PLUGS
.173 " MINIATURE TELEPHONE PLUGS BANTAM TYPE
.173 " MINIATURE TELEPHONE PLUGS BANTAM TYPE
.173" MINIATURE TELEPHONE PLUGS BANTAM TYPE
FEATURES
Miniature telephone twin plugs with two 2-conductor or two
3-conductor fingers, designed to mate with TT Twin-Jax
TT-Jax
bushing and compatible tip and ring springs. Approximately
1/2 the size of standard phone plugs; yet retains uniformity,
dependability of high-quality phone plugs. The phone plugs
are exceptionally light, small and rugged. Plug fingers can
easily be removed and replaced.
• Minimum Space: Plugs fit .313" centers, horizontally
• Self-Aligning: Plug fingers compensate for minor
• Polarizing: Handle notches identify location of each finger.
• Tip Monitoring: Handle ports permit probe insertion to
• Terminating and Looping Plugs: OEMs can fabricate
• Sleeve Plugs: For looping, terminating and single cable
• Ease of Assembly/Disassembly: Refer to illustration below
SPECIFICATIONS
Tip Rod, Ring, Sleeve and Body: Copper alloy,
natural finish.
Terminals and Terminal Screws: Copper alloy,
natural finish.
Insulation: Thermoplastic.
Handle, Sleeve Plugs: Molded plastic.
1. DISASSEMBLY: Place plug on edge as shown. Push down
2. CABLE INSTALLATION: Fold braided shield on cable back
3. To bridge sleeves (common connection), place free end of
TT261: Two electrically-independent 2-conductor fingers in a black
handle. Can be used with single or dual cables for independent tip
circuits with common sleeve or separate sleeve circuits.
or vertically.
variations in jack spacing.
monitor tip circuits.
cross-wired plugs, i.e., tip-to-sleeve, tip-to-ring, etc.,
according to individual requirements. OEMs can also
wire-in resistors, RCL networks, etc. for standard and
special terminating applications. Switchcraft will build
looping and terminating TT-Twin Plugs on special order,
where quantities warrant.
applications, sleeve plugs seal off unused handle open-ing(s).
Sleeve plugs also make a bridged (common) sleeve
connection by holding braided shield in place in second
plug.On special order, TT-Twin Plugs can be supplied
with one 2-conductor finger and one 3-conductor finger.
for assembly/disassembly procedure; no handle retaining
screws required. Tip and ring terminations are screw-type
screws supplied).
and back on metal lip on finger (inside notch) with small
screwdriver and slip plug finger out of handle. Turn plug
over and repeat for other finger.
over insulation. Insert leads through rear of plug finger, and
screw finger (clockwise) onto cable with twisting motion
until lead terminations lineup with threaded tip and/or ring
openings. Fasten terminals on both fingers with screws
provided.
braided shield in remaining finger sleeve opening. Press
sleeve plug firmly in place.
®
, and other phone jacks with a .176" inside diameter
DIMENSIONS ARE FOR REFERENCE ONLY
®
,
TT263: 6-circuit plug consists of two electrically-independent
3-conductor fingers with black handle. Can use single or dual
cables for two electrically-independent 3-conductor fingers or
common tip, ring and/or sleeve circuits.
4. ASSEMBLY: Align grooves in fingers with internal handle
1. TT-Twin Plug plugs can be supplied with one, 2-conductor plug finger and
2. Switchcraft Part Numbers. See additional mating jacks in this section.
3. Switchcraft Replacement screw P2240, Terminal P2642. 2 each required
4. Replacement Hole Plug Switchcraft T2318 (Black) T2319 (Red).
Number
TT261
TT261
TT263
Part
one, 3-conductor plug finger in the same handle (on special order).
with 2-conductor twin plugs; 4 each required with 3-conductor twin plugs.
ribs and insert fingers into rear of handle. Push fingers in
until lips or rear of fingers snap into notches on handle.
1.
1
Cond. Terminals
Note: Contact your Switchcraft Representative for price and delivery
(mm)
Inch
2
3
NOTCH
4.
Screw
LIP ON
FINGER
3
2. & 3.
Typical
PHONE: 773 792 - 2700
Mating
TT32B
TT31
Jack
GROOVE
® Registered trademark of Switchcraft, Inc.
2
NOTCH
Handle
Black
Black
LIP
INTERNAL RIB
FINGER
Number
T2300-2
Handle
T2316
Part
TT261
TT263
MIL Type
M642/13-3
BRAIDED
SHIELD
Number
TT263
–