PIC16F628AT-E/SS Microchip Technology, PIC16F628AT-E/SS Datasheet - Page 93

• Manufacturer Part Number: PIC16F628AT-E/SS
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SSOP,20PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F628AT-E/SS

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 224 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 20-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3DBF648 - BOARD DAUGHTER ICEPIC3AC162053 - HEADER INTERFACE ICD,ICD2 18DIP
• Data Converters: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13.3
To read a data memory location, the user must write the
address to the EEADR register and then set control bit
RD (EECON1<0>). The data is available, in the very
next cycle, in the EEDATA register; therefore it can be
read in the next instruction. EEDATA will hold this value
until another read or until it is written to by the user
(during a write operation).
EXAMPLE 13-1:
13.4
To write an EEPROM data location, the user must first
write the address to the EEADR register and the data
to the EEDATA register. Then the user must follow a
specific sequence to initiate the write for each byte.
EXAMPLE 13-2:
The write will not initiate if the above sequence is not
followed exactly (write 55h to EECON2, write AAh to
EECON2, then set WR bit) for each byte. We strongly
recommend that interrupts be disabled during this
code segment. A cycle count is executed during the
required sequence. Any number that is not equal to the
required cycles to execute the required sequence will
cause the data not to be written into the EEPROM.
Additionally, the WREN bit in EECON1 must be set to
enable write. This mechanism prevents accidental
writes to data EEPROM due to errant (unexpected)
code execution (i.e., lost programs). The user should
keep the WREN bit clear at all times, except when
updating EEPROM. The WREN bit is not cleared
by hardware.
After a write sequence has been initiated, clearing the
WREN bit will not affect this write cycle. The WR bit will
be inhibited from being set unless the WREN bit is set.
© 2009 Microchip Technology Inc.
BSF
MOVLW
MOVWF
BSF
MOVF
BCF
BSF
BSF
BCF
BTFSC
GOTO
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF INTCON, GIE
Reading the EEPROM Data
Memory
Writing to the EEPROM Data
Memory
STATUS, RP0
CONFIG_ADDR
EEADR
EECON1, RD
EEDATA, W
STATUS, RP0
STATUS, RP0
EECON1, WREN
INTCON, GIE
INTCON,GIE
$-2
55h
EECON2
AAh
EECON2
EECON1,WR
DATA EEPROM READ
DATA EEPROM WRITE
;Bank 1
;
;Address to read
;EE Read
;W = EEDATA
;Bank 0
;Bank 1
;Enable write
;Disable INTs.
;
;Write 55h
;
;Write AAh
;Set WR bit
;begin write
;Enable INTs.
;See AN576
PIC16F627A/628A/648A
At the completion of the write cycle, the WR bit is
cleared in hardware and the EE Write Complete
Interrupt Flag bit (EEIF) is set. The user can either
enable this interrupt or poll this bit. The EEIF bit in the
PIR1 registers must be cleared by software.
13.5
Depending on the application, good programming
practice may dictate that the value written to the Data
EEPROM should be verified (Example 13-3) to the
desired value to be written. This should be used in
applications where an EEPROM bit will be stressed
near the specification limit.
EXAMPLE 13-3:
13.6
There are conditions when the device may not want to
write to the data EEPROM memory. To protect against
spurious EEPROM writes, various mechanisms have
been built-in. On power-up, WREN is cleared. Also
when enabled, the Power-up Timer (72 ms duration)
prevents EEPROM write.
The write initiate sequence and the WREN bit together
help prevent an accidental write during brown-out,
power glitch or software malfunction.
;
;Is the value written (in W reg) and
;read (in EEDATA) the same?
;
BSF
MOVF
BSF
SUBWF
BTFSS
GOTO
:
:
Write Verify
Protection Against Spurious Write
STATUS, RP0 ;Bank 1
EEDATA, W
EECON1, RD ;Read the
EEDATA, W
STATUS, Z
WRITE_ERR
WRITE VERIFY
;value written
;
;Is difference 0?
;NO, Write error
;YES, Good write
;Continue program
DS40044G-page 93