ST7FOXK1 STMicroelectronics, ST7FOXK1 Datasheet - Page 188
ST7FOXK1
Manufacturer Part Number
ST7FOXK1
Description
Low cost flash 8bit micro
Manufacturer
STMicroelectronics
Datasheet
1.ST7FOXK1.pdf
(226 pages)
Specifications of ST7FOXK1
4 To 8 Kbytes Single Voltage Extended Flash (xflash) Program Memory With Read-out Protection In-circuit Programming And In-application Programming (icp And Iap) Endurance
1K write/erase cycles guaranteed Data retention
Clock Sources
Internal trimmable 8 MHz RC oscillator, auto wakeup internal low power - low frequency oscillator, crystal/ceramic resonator or external clock
Five Power Saving Modes
Halt, Active-Halt, Auto Wakeup from Halt, Wait and Slow
A/d Converter
up to 10 input channels
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ST7FOXK1T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
ST7FOXK1T6TR
Manufacturer:
STMicroelectronics
Quantity:
10 000
- Current page: 188 of 226
- Download datasheet (4Mb)
Electrical characteristics
12.2
188/226
Figure 82. Pin input voltage
Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 66.
1. Directly connecting the RESET and I/O pins to V
2. I
internal reset is generated or an unexpected change of the I/O configuration occurs (for example, due to a
corrupted Program Counter). To guarantee safe operation, this connection has to be done through a pull-
up or pull-down resistor (typical: 4.7 kΩ for RESET, 10 kΩ for I/Os). Unused I/O pins must be tied in the
same way to V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
pads, there is no positive injection current, and the corresponding V
INJ(PIN)
V
V
V
Symbol
ESD(HBM)
ESD(CDM)
DD
V
- V
IN
must never be exceeded. This is implicitly insured if V
SS
Voltage characteristics
DD
or V
Electrostatic discharge voltage (Charge Device
Electrostatic discharge voltage (Human Body
SS
IN
according to their reset configuration.
>V
DD
Input voltage on any pin
while a negative injection is induced by V
V
Supply voltage
IN
Ratings
model)
model)
DD
or V
SS
ST7 PIN
(1)(2)
could damage the device if an unintentional
IN
ST7FOXF1, ST7FOXK1, ST7FOXK2
maximum is respected. If V
IN
maximum must always be respected
IN
V
<V
INJ(PIN)
Maximum value
see
SS
SS
-0.3 to V
. For true open-drain
Section 12.8.3 on page
value. A positive
7.0
DD
203
IN
+0.3
maximum
Unit
V
Related parts for ST7FOXK1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: