ST7FOXK1 STMicroelectronics, ST7FOXK1 Datasheet - Page 25

• Manufacturer Part Number: ST7FOXK1
• Description: Low cost flash 8bit micro
• Manufacturer: STMicroelectronics

Specifications of ST7FOXK1

• 4 To 8 Kbytes Single Voltage Extended Flash (xflash) Program Memory With Read-out Protection In-circuit Programming And In-application Programming (icp And Iap) Endurance: 1K write/erase cycles guaranteed Data retention
• Clock Sources: Internal trimmable 8 MHz RC oscillator, auto wakeup internal low power - low frequency oscillator, crystal/ceramic resonator or external clock
• Five Power Saving Modes: Halt, Active-Halt, Auto Wakeup from Halt, Wait and Slow
• A/d Converter: up to 10 input channels

ST7FOXF1, ST7FOXK1, ST7FOXK2
4.3.2
4.4
Note:
Caution:
1
2
3
4
Depending on the ICP Driver code downloaded in RAM, Flash memory programming can
be fully customized (number of bytes to program, program locations, or selection of the
serial communication interface for downloading).
In Application Programming (IAP)
This mode uses an IAP Driver program previously programmed in Sector 0 by the user (in
ICP mode).
This mode is fully controlled by user software. This allows it to be adapted to the user
application, (user-defined strategy for entering programming mode, choice of
communications protocol used to fetch the data to be stored etc.)
IAP mode can be used to program any memory areas except Sector 0, which is Write/Erase
protected to allow recovery in case errors occur during the programming operation.
ICC interface
ICP needs a minimum of 4 and up to 6 pins to be connected to the programming tool. These
pins are:
If the ICCCLK or ICCDATA pins are only used as outputs in the application, no signal
isolation is necessary. As soon as the Programming Tool is plugged to the board, even if an
ICC session is not in progress, the ICCCLK and ICCDATA pins are not available for the
application. If they are used as inputs by the application, isolation such as a serial resistor
has to be implemented in case another device forces the signal. Refer to the Programming
Tool documentation for recommended resistor values.
During the ICP session, the programming tool must control the RESET pin. This can lead to
conflicts between the programming tool and the application reset circuit if it drives more than
5mA at high level (push pull output or pull-up resistor<1 k
to isolate the application RESET circuit in this case. When using a classical RC network with
R>1 k
additional components are needed. In all cases the user must ensure that no external reset
is generated by the application during the ICC session.
The use of pin 7 of the ICC connector depends on the Programming Tool architecture. This
pin must be connected when using most ST Programming Tools (it is used to monitor the
application power supply). Please refer to the Programming Tool manual.
In “enabled option byte” mode (38-pulse ICC mode), the internal RC oscillator is forced as a
clock source, regardless of the selection in the option byte. In “disabled option byte” mode
(35-pulse ICC mode), pin 9 has to be connected to the PB1/CLKIN pin of the ST7 when the
clock is not available in the application or if the selected clock option is not programmed in
the option byte.
During normal operation the ICCCLK pin must be internally or externally pulled- up (external
pull-up of 10 kΩ mandatory in noisy environment) to avoid entering ICC mode unexpectedly
RESET: device reset
V
ICCCLK: ICC output serial clock pin
ICCDATA: ICC input serial data pin
OSC1: main clock input for external source
V
Ω
SS
DD
or a reset management IC with open drain output and pull-up resistor>1 k
: device power supply ground
: application board power supply (optional, see Note 3)
Ω
). A schottky diode can be used
Flash programmable memory
Ω
, no
25/226