S9S12G64F0CLFR Freescale Semiconductor, S9S12G64F0CLFR Datasheet - Page 1019

• Manufacturer Part Number: S9S12G64F0CLFR
• Description: 16-bit Microcontrollers - MCU S12 Core,64K FLASH AU
• Manufacturer: Freescale Semiconductor

Specifications of S9S12G64F0CLFR

• Rohs: yes
• Core: S12
• Processor Series: MC9S12G
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 1 MHz
• Program Memory Size: 64 KB
• Data Ram Size: 8 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 3.13 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-48
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit, 12 bit
• A/d Channels Available: 12
• Interface Type: SPI
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 40
• Number Of Timers: 8
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 3.13 V

The reserved nonvolatile information register accessed by the Program Once command cannot be erased
and any attempt to program one of these phrases a second time will not be allowed. Valid phrase index
values for the Program Once command range from 0x0000 to 0x0007. During execution of the Program
Once command, any attempt to read addresses within P-Flash will return invalid data.
28.4.6.7
The Erase All Blocks operation will erase the entire P-Flash and EEPROM memory space.
Upon clearing CCIF to launch the Erase All Blocks command, the Memory Controller will erase the entire
Flash memory space and verify that it is erased. If the Memory Controller verifies that the entire Flash
memory space was properly erased, security will be released. During the execution of this command
(CCIF=0) the user must not write to any Flash module register. The CCIF flag will set after the Erase All
Blocks operation has completed.
Freescale Semiconductor
1
1
If a Program Once phrase is initially programmed to 0xFFFF_FFFF_FFFF_FFFF, the Program Once command will
be allowed to execute again on that same phrase.
As found in the memory map for FTMRG96K1.
Register
Register
FSTAT
FSTAT
Erase All Blocks Command
CCOBIX[2:0]
Table 28-44. Erase All Blocks Command FCCOB Requirements
MGSTAT1
MGSTAT0
MGSTAT1
MGSTAT0
ACCERR
ACCERR
Error Bit
Error Bit
FPVIOL
FPVIOL
000
Table 28-45. Erase All Blocks Command Error Handling
Table 28-43. Program Once Command Error Handling
MC9S12G Family Reference Manual, Rev.1.23
Set if CCOBIX[2:0] != 101 at command launch
Set if command not available in current mode (see
Set if an invalid phrase index is supplied
Set if the requested phrase has already been programmed
None
Set if any errors have been encountered during the verify operation
Set if any non-correctable errors have been encountered during the verify
operation
Set if CCOBIX[2:0] != 000 at command launch
Set if command not available in current mode (see
Set if any area of the P-Flash or EEPROM memory is protected
Set if any errors have been encountered during the verify operation
Set if any non-correctable errors have been encountered during the verify
operation
1
0x08
FCCOB Parameters
Error Condition
Error Condition
Not required
96 KByte Flash Module (S12FTMRG96K1V1)
Table
Table
28-27)
28-27)
1
1
1021