FPF2163 Fairchild Semiconductor, FPF2163 Datasheet
FPF2163
Specifications of FPF2163
Related parts for FPF2163
FPF2163 Summary of contents
Page 1
... The FPF2163 has an auto-restart feature which will turn the switch on again after 450ms if the ON pin is still active. The FPF2164 does not have this auto-restart feature so the switch will remain off until the ON pin is cycled ...
Page 2
... Typical Application Circuit OFF ON Functional Block Diagram V IN UVLO ON THERMAL SHUTDOWN FPF2163/4/5 Rev OUT FPF2163/4/5 FLAGB ON ISET GND CONTROL LOGIC CURRENT LIMIT 2 TO LOAD REVERSE CURRENT BLOCKING V OUT ISET FLAGB GND www.fairchildsemi.com ...
Page 3
... Electrostatic Discharge Protection Recommended Operating Range Parameter V IN Ambient Operating Temperature Electrical Characteristics V = 1.8 to 5.5V -40 to +85°C unless otherwise noted. Typical values are Parameter Basic Operation Operating Voltage Quiescent Current FPF2163/4/5 Rev ISET 7 GND FLAGB OUT 2X2 MicroFET-6 Current Limit Set Input: A resistor from ISET to ground sets the current limit for the switch. ...
Page 4
... Dynamic Delay On Time Delay Off Time V Rise Time OUT V Fall Time OUT Over Current Blanking Time Auto-Restart Time Short Circuit Response Time Note 1: Package power dissipation on 1square inch pad copper board. FPF2163/4/5 Rev. I Symbol Conditions V = 3.3V 200mA OUT 3.3V 200mA OUT ...
Page 5
... SUPPLY VOLTAGE (V) Figure 3. V High Voltage vs. Input Voltage ON 200 190 180 170 160 150 140 130 120 110 100 SUPPLY VOLTAGE(V) Figure FPF2163/4/5 Rev. I 100 4.5 5 5.5 6 -40 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 1 ...
Page 6
... OFF -40 - JUNCTION TEMPERATURE (°C) J Figure vs. Temperature ON OFF 33 32.5 32 31.5 31 30.5 30 29.5 -40 - JUNCTION TEMPERATURE (°C) J Figure 11. T vs. Temperature BLANK FPF2163/4/5 Rev. I 900 V = 5.5V IN 880 R = 345 Ohms SET 860 840 820 800 780 760 740 720 700 - (V) 1000 V R 100 -40 500 495 ...
Page 7
... OUT 10mA/DIV V OUT 2V/DIV 100µs/DIV Figure 15. td Response 2V/DIV I OUT 5A/DIV V OUT 2V/DIV 20µs/DIV Figure 17. Short Circuit Response Time (Output shorted to GND) FPF2163/4/5 Rev DRV 2V/DIV V FLAGB 2V/DIV I OUT 500mA/DIV C = 10µ 0.1µF IN OUT R = 500Ω 392Ω L SET ...
Page 8
... IN 2V/DIV I OUT 500mA/DIV V OUT 2V/DIV 50µs/DIV Figure 19. Current Limit Response Time (Output is loaded by 2.2Ω, C Note 2: V signal forces the device to go into overcurrent condition by loading. DRV FPF2163/4/5 Rev 2V/DIV V ON 2V/DIV I OUT 500mA/DIV V OUT 2V/DIV = 0.1µF) (Output is loaded by 2.2Ω, C ...
Page 9
... Fault Reporting Upon the detection of an over-current, an input undervoltage over-temperature condition, the FLAGB signals the fault mode by activating LO. For the FPF2163 and FPF2164, the FLAGB goes LO at the end of the blanking time while FLAGB goes LO immediately for the FPF2165. FLAGB remains LO through the Auto-Restart Time for the FPF2165 ...
Page 10
... Application Information Typical Application Battery 1.8V-5.5V OFF 4.7µF Setting Current Limit The FPF2163, FPF2164, and FPF2165 have a current limit which is set with an external resistor connected between ISET and GND. This resistor is selected by using the following equation, 275 SET I LIM Ohms and that of I ...
Page 11
... This concern applies when the switch is set at higher current limit value and an overcurrent condition occurs. In this case power dissipation of the switch ( OUT maximum absolute power dissipation of 1.2W. FPF2163/4/5 Rev. I (max) (5) LIM , V and GND will help OUT (max)) could exceed the LIM 11 www.fairchildsemi.com ...
Page 12
... Dimensional Outline and Pad Layout FPF2163/4/5 Rev www.fairchildsemi.com ...
Page 13
... Definition of Terms Datasheet Identification Product Status Advance Information Formative / In Design Preliminary First Production No Identification Needed Full Production Obsolete Not In Production FPF2163/4/5 Rev. I ® Programmable Active Droop™ ® SM QFET QS™ Quiet Series™ RapidConfigure™ ™ Saving our world, 1mW/W/ time™ ...