LTC3716EG Linear Technology, LTC3716EG Datasheet - Page 20

• Manufacturer Part Number: LTC3716EG
• Description: IC SW REG STP-DN 5BIT SYNC36SSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC3716EG

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.6 ~ 1.75 V
• Current - Output: 35mA
• Frequency - Switching: 120kHz ~ 310kHz
• Voltage - Input: 4 ~ 36 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 36-SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Power - Output: -

APPLICATIO S I FOR ATIO
LTC3716
If the external frequency (f
lator frequency f
pulling up the PLLFLTR pin. When the external frequency
is less than f
down the PLLFLTR pin. If the external and internal fre-
quencies are the same but exhibit a phase difference, the
current sources turn on for an amount of time correspond-
ing to the phase difference. Thus the voltage on the
PLLFLTR pin is adjusted until the phase and frequency of
the external and internal oscillators are identical. At this
stable operating point the phase comparator output is
open and the filter capacitor C
LTC3716 PLLIN pin must be driven from a low impedance
source such as a logic gate located close to the pin.
The loop filter components (C
current pulses from the phase detector and provide a
stable input to the voltage controlled oscillator. The filter
components C
acquires lock. Typically R
0.1 F.
Minimum On-Time Considerations
Minimum on-time, t
that the LTC3716 is capable of turning on the top MOSFET.
It is determined by internal timing delays and the gate
charge required to turn on the top MOSFET. Low duty cycle
applications may approach this minimum on-time limit
and care should be taken to ensure that:
If the duty cycle falls below what can be accommodated by
the minimum on-time, the LTC3716 will begin to skip
cycles resulting in variable frequency operation. The out-
put voltage will continue to be regulated, but the ripple
current and ripple voltage will increase.
The minimum on-time for the LTC3716 is generally less
than 200ns. However, as the peak sense voltage de-
creases, the minimum on-time gradually increases. This is
of particular concern in forced continuous applications
with low ripple current at light loads. If the duty cycle drops
below the minimum on-time limit in this situation, a
20
t
ON MIN
0SC
V f
LP
V
IN
OUT
, current is sunk continuously, pulling
0SC
and R
U
ON(MIN)
, current is sourced continuously,
LP
U
PLLIN
LP
, is the smallest time duration
determine how fast the loop
=10k and C
LP
) is greater than the oscil-
LP
, R
holds the voltage. The
W
LP
) smooth out the
LP
is 0.01 F to
U
significant amount of cycle skipping can occur with corre-
spondingly larger ripple current and voltage ripple.
If an application can operate close to the minimum
on-time limit, an inductor must be chosen that has a low
enough inductance to provide sufficient ripple amplitude
to meet the minimum on-time requirement. As a general
rule, keep the inductor ripple current of each phase equal
to or greater than 15% of I
FCB Pin Operation
The FCB pin can be used to regulate a secondary winding
or as a logic level input. Continuous operation is forced
when the FCB pin drops below 0.6V. During continuous
mode, current flows continuously in the transformer pri-
mary. The secondary winding(s) supply current only when
the bottom, synchronous switch is on. When primary load
currents are low and/or the V
synchronous switch may not be on for a sufficient amount
of time to transfer power from the output capacitor to the
secondary load. Forced continuous operation will support
secondary windings providing there is sufficient synchro-
nous switch duty factor. Thus, the FCB input pin removes
the requirement that power must be drawn from the
inductor primary in order to extract power from the
auxiliary winding(s). With the loop in continuous mode,
the auxiliary output(s) may nominally be loaded without
regard to the primary output load.
The secondary output voltage V
shown in Figure 5a by the turns ratio N of the transformer:
However, if the controller goes into Burst Mode operation
and halts switching due to a light primary load current,
then V
V
where R5 and R6 are shown in Figure 5a.
If V
temporary continuous switching operation until V
again above its minimum.
SEC
V
V
SEC
SEC
SEC MIN
to the FCB pin sets a minimum voltage V
SEC
(
drops below this level, the FCB voltage forces
(N + 1) V
will droop. An external resistive divider from
)
. 0 6
V
OUT
1
R
R
6
5
OUT(MAX)
IN
/V
SEC
OUT
at V
is normally set as
ratio is low, the
IN(MAX)
SEC(MIN)
.
SEC
:
is