PIC18F1230-I/SO Microchip Technology, PIC18F1230-I/SO Datasheet - Page 142

• Manufacturer Part Number: PIC18F1230-I/SO
• Description: IC PIC MCU FLASH 2KX16 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F1230-I/SO

• Core Size: 8-Bit
• Program Memory Size: 4KB (2K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 18-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 40MHz
• No. Of Timers: 2
• Package: 18SOIC W
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Interface Type: USART
• On-chip Adc: 4-chx10-bit
• Number Of Timers: 2
• Processor Series: PIC18F
• Core: PIC
• Data Ram Size: 256 B
• Maximum Clock Frequency: 40 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• Height: 2.31 mm
• Length: 11.53 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 7.49 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F1230/1330
FIGURE 14-23:
14.11.3
The PWMPIN Configuration bit determines the PWM
output pins to be PWM output pins, or digital I/O pins,
after the device comes out of Reset. If the PWMPIN
Configuration bit is unprogrammed (default), the
PWMEN2:PWMEN0 control bits will be cleared on a
device Reset. Consequently, all PWM outputs will be
tri-stated and controlled by the corresponding PORT
and TRIS registers. If the PWMPIN Configuration bit is
programmed low, the PWMEN2:PWMEN0 control bits
will be set to ‘100’ on a device Reset:
All PWM pins will be enabled for PWM output and will
have the output polarity defined by the HPOL and
LPOL Configuration bits.
14.12 PWM Fault Input
There is one Fault input associated with the PWM
module. The main purpose of the input Fault pin is to
disable the PWM output signals and drive them into an
inactive state. The action of the Fault input is performed
DS39758D-page 142
Note:
PWM OUTPUT PIN RESET STATES
PWM Signal from Module
PWM Pin Enable
Data Bus
WR PORT
WR TRIS
RD TRIS
RD PORT
I/O pin has protection diodes to V
PWM I/O PIN BLOCK DIAGRAM
Data Latch
TRIS Latch
D
D
CK
CK
Q
Q
Q
Q
DD
and V
SS
. PWM polarity selection logic not shown for clarity.
1
0
directly in hardware so that when a Fault occurs, it can
be managed quickly and the PWMs outputs are put into
an inactive state to save the power devices connected
to the PWMs.
The PWM Fault input is FLTA, which can come from
I/O pins, the CPU or another module. The FLTA pin is
an active-low input so it is easy to “OR” many sources
to the same input.
The FLTCONFIG register (Register 14-8) defines the
settings of the FLTA input.
14.12.1
By setting the bit FLTAEN in the FLTCONFIG register,
the corresponding Fault input is enabled. If FLTAEN bit
is cleared, then the Fault input has no effect on the
PWM module.
Q
Note:
EN
D
The inactive state of the PWM pins is
dependent on the HPOL and LPOL Con-
figuration bit settings, which define the
active and inactive state for PWM outputs.
FAULT PIN ENABLE BIT
V
V
P
N
DD
SS
 2009 Microchip Technology Inc.
TTL or
Schmitt
Trigger
I/O pin