PIC16F74-I/P Microchip Technology, PIC16F74-I/P Datasheet - Page 162

• Manufacturer Part Number: PIC16F74-I/P
• Description: IC MCU FLASH 4KX14 A/D 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F74-I/P

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 33
• Program Memory Type: FLASH
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 33
• Ram Memory Size: 192Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 33
• Interface Type: I2C/SPI/USART
• On-chip Adc: 8-chx8-bit
• Number Of Timers: 3
• Processor Series: PIC16F
• Core: PIC
• Data Ram Size: 192 B
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PICmicro MID-RANGE MCU FAMILY
10.1
DS31010A-page 10-2
Introduction
Some devices have an 8-bit wide Parallel Slave Port (PSP). This port is multiplexed onto one of
the devices I/O ports. The PORT operates as an 8-bit wide Parallel Slave Port, or microprocessor
port, when the PSPMODE control bit is set. In this mode, the input buffers are TTL.
In slave mode the module is asynchronously readable and writable by the external world through
RD control input pin and the WR control input pin.
It can directly interface to an 8-bit microprocessor data bus. The external microprocessor can
read or write the PORT latch as an 8-bit latch. Setting the PSPMODE bit enables port pins to be
the RD input, the WR input, and the CS (chip select) input.
There are actually two 8-bit latches, one for data-out (from the PICmicro) and one for data input.
The user writes 8-bit data to PORT data latch and reads data from the port pin latch (note that
they have the same address). In this mode, the TRIS register is ignored, since the microproces-
sor is controlling the direction of data flow.
Figure 10-1
Figure 10-1: PORTD and PORTE Block Diagram (Parallel Slave Port)
Note 1: At present the Parallel Slave Port (PSP) is only multiplexed onto PORTD and
Note 2: In this mode the PORTD and PORTE input buffers are TTL. The control bits for the
Note: I/O pins have protection diodes to V
Data bus
One bit of PORTD
Set interrupt flag
PSPIF
PORTE. The microprocessor port becomes enabled when the PSPMODE bit is set.
In this mode, the user must make sure that PORTD and PORTE are configured as
digital I/O. That is, peripheral modules multiplexed onto the PSP functions are dis-
abled (such as the A/D).
When PORTE is configured for digital I/O. PORTD will override the values in the
TRISD register.
PSP operation are located in TRISE.
shows the block diagram for the PSP.
RD Port
WR Port
Q
D
CK
EN
EN
EN
D
Q
DD
and V
SS
.
TTL
Read
Chip Select
Write
1997 Microchip Technology Inc.
TTL
TTL
TTL
PSP7:PSP0
RD
CS
WR