PIC16F74-I/P Microchip Technology, PIC16F74-I/P Datasheet - Page 232

• Manufacturer Part Number: PIC16F74-I/P
• Description: IC MCU FLASH 4KX14 A/D 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F74-I/P

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 33
• Program Memory Type: FLASH
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 33
• Ram Memory Size: 192Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 33
• Interface Type: I2C/SPI/USART
• On-chip Adc: 8-chx8-bit
• Number Of Timers: 3
• Processor Series: PIC16F
• Core: PIC
• Data Ram Size: 192 B
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PICmicro MID-RANGE MCU FAMILY
15.3.6
DS31015A-page 15-12
SS
not optional
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
Write to
SSPBUF
SDO
SDI
(SMP = 0)
Input
Sample
(SMP = 0)
SSPIF
Interrupt
Flag
SSPSR to
SSPBUF
Slave Select Mode
When in slave select mode, the SS pin allows multi-drop for multiple slaves with a single
master. The SPI must be in slave mode (SSPCON<3:0> = 04h) and the TRIS bit, for the
SS pin, must be set for the slave select mode to be enabled. When the SS pin is low, trans-
mission and reception are enabled and the SDO pin is driven. When the SS pin goes high,
the SDO pin is no longer driven, even if in the middle of a transmitted byte, and becomes
a floating output. External pull-up/ pull-down resistors may be desirable, depending on the
application.
When the SPI is in Slave Mode with SS pin control enabled, (SSPCON<3:0> = 0100) the SPI
module will reset if the SS pin is set to V
set, then the SS pin control must be enabled.
When the SPI module resets, the bit counter is forced to 0. This can be done by either by forcing
the SS pin to a high level or clearing the SSPEN bit
To emulate two-wire communication, the SDO pin can be connected to the SDI pin. When the
SPI needs to operate as a receiver the SDO pin can be configured as an input. This disables
transmissions from the SDO. The SDI can always be left as an input (SDI function) since it cannot
create a bus conflict.
Figure 15-5:
bit7
bit7
SPI Mode Waveform (Slave Select Mode With CKE = 1)
bit6
bit5
bit4
DD
. If the SPI is used in Slave Mode with the CKE bit is
bit3
(Figure
bit2
15-6).
bit1
1997 Microchip Technology Inc.
bit0
bit0
Next Q4 cycle
after Q2