PIC16F74-I/P Microchip Technology, PIC16F74-I/P Datasheet - Page 267

• Manufacturer Part Number: PIC16F74-I/P
• Description: IC MCU FLASH 4KX14 A/D 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F74-I/P

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 33
• Program Memory Type: FLASH
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 33
• Ram Memory Size: 192Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 33
• Interface Type: I2C/SPI/USART
• On-chip Adc: 8-chx8-bit
• Number Of Timers: 3
• Processor Series: PIC16F
• Core: PIC
• Data Ram Size: 192 B
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

16.4.1
1997 Microchip Technology Inc.
Slave Mode
In slave mode, the SCL and SDA pins must be configured as inputs (TRIS bits set). The SSP
module will override the input state with the output data when required (slave-transmitter).
When an address is matched or the data transfer after an address match is received, the hard-
ware automatically will generate the acknowledge (ACK) pulse, and then load the SSPBUF reg-
ister with the received value currently in the SSPSR register.
There are certain conditions that will cause the SSP module not to give this ACK pulse. These
are if either (or both):
a)
b)
In this case, the SSPSR register value is not loaded into the SSPBUF, but bit SSPIF and SSPOV
bits are set.
tus of the BF and SSPOV bits. The shaded cells show the condition where user software did not
properly clear the overflow condition. The BF flag bit is cleared by reading the SSPBUF register
while the SSPOV bit is cleared through software.
The SCL clock input must have a minimum high and low time for proper operation. The high and
low times of the I
parameter 100
The buffer full bit, BF (SSPSTAT<0>), was set before the transfer was received.
The overflow bit, SSPOV (SSPCON<6>), was set before the transfer was received.
Table 16-2
and
2
C specification as well as the requirement of the SSP module are given in
parameter 101
shows what happens when a data transfer byte is received, given the sta-
of the
“Electrical Specifications”
Section 16. BSSP
section.
DS31016A-page 16-17
16