AT91SAM9XE128-QU Atmel, AT91SAM9XE128-QU Datasheet - Page 223

• Manufacturer Part Number: AT91SAM9XE128-QU
• Description: MCU ARM9 128K FLASH 208-PQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9XE128-QU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-MQFP, 208-PQFP
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: 2-Wire, EBI, I2S, SPI, USART
• Maximum Clock Frequency: 180 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM9XE-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9XE-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: AT91SAM9XE-EK - KIT EVAL FOR AT91SAM9XEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

23.11.3
Figure 23-28. NWAIT Assertion in Write Access: Ready Mode (EXNW_MODE = 11)
6254C–ATARM–22-Jan-10
internally synchronized
NBS0, NBS1,
NBS2, NBS3,
A0,A1
NWAIT signal
Ready Mode
D[31:0]
NWAIT
A
[25:2]
NWE
MCK
NCS
6
In Ready mode (EXNW_MODE = 11), the SMC behaves differently. Normally, the SMC begins
the access by down counting the setup and pulse counters of the read/write controlling signal. In
the last cycle of the pulse phase, the resynchronized NWAIT signal is examined.
If asserted, the SMC suspends the access as shown in
deassertion, the access is completed: the hold step of the access is performed.
This mode must be selected when the external device uses deassertion of the NWAIT signal to
indicate its ability to complete the read or write operation.
If the NWAIT signal is deasserted before the end of the pulse, or asserted after the end of the
pulse of the controlling read/write signal, it has no impact on the access length as shown in
ure
23-29.
4
5
4
3
3
AT91SAM9XE128/256/512 Preliminary
2
1
2
Write cycle
EXNW_MODE = 11 (Ready mode)
WRITE_MODE = 1 (NWE_controlled)
NWE_PULSE = 5
NCS_WR_PULSE = 7
0
1
Wait STATE
0
1
Figure 23-28
0
1
0
and
Figure
23-29. After
Fig-
223