ATMEGA169PV-8AUR Atmel, ATMEGA169PV-8AUR Datasheet - Page 311

• Manufacturer Part Number: ATMEGA169PV-8AUR
• Description: MCU AVR 16KB FLASH 16MHZ 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169PV-8AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Package: 64TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 54
• Interface Type: SPI/USART/USI
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

27.8.1
27.8.2
8018P–AVR–08/10
Serial Programming Pin Mapping
Serial Programming Algorithm
Table 27-14. Pin Mapping Serial Programming
Figure 27-10. Serial Programming and Verify
Notes:
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low: > 2 CPU clock cycles for f
High: > 2 CPU clock cycles for f
When writing serial data to the ATmega169P, data is clocked on the rising edge of SCK.
When reading data from the ATmega169P, data is clocked on the falling edge of SCK. See
ure 27-11 on page 313
To program and verify the ATmega169P in the serial programming mode, the following
sequence is recommended (See four byte instruction formats in
1. Power-up sequence:
Apply power between V
tems, the programmer can not guarantee that SCK is held low during power-up. In this
1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the
2. V
Symbol
MOSI
MISO
SCK
XTAL1 pin.
CC
- 0.3V < AVCC < V
for timing details.
CC
and GND while RESET and SCK are set to “0”. In some sys-
MOSI
MISO
SCK
ck
ck
CC
Pins
PB2
PB3
PB1
< 12 MHz, 3 CPU clock cycles for f
< 12 MHz, 3 CPU clock cycles for f
+ 0.3V, however, AVCC should always be within 1.8V - 5.5V
XTAL1
RESET
GND
(1)
AVCC
VCC
+1.8V - 5.5V
+1.8V - 5.5V
I/O
O
I
I
Table 27-16 on page
(2)
ck
ck
ATmega169P
>= 12 MHz
>= 12 MHz
Serial Data out
Serial Data in
Description
Serial Clock
314):
Fig-
311