AT89C5131A-PUTUM Atmel, AT89C5131A-PUTUM Datasheet - Page 134

• Manufacturer Part Number: AT89C5131A-PUTUM
• Description: IC 8051 MCU FLASH 32K USB 32QFN
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5131A-PUTUM

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: LED, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Core: 8051
• Processor Series: AT89x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 48 MHz
• Data Ram Size: 1.25 KB
• Number Of Programmable I/os: 34
• Number Of Timers: 16 bit
• Operating Supply Voltage: 2.7 V to 5.5 V
• Mounting Style: SMD/SMT
• Height: 0.95 mm
• Interface Type: 2-Wire, EUART, SPI, USB
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCUAT89STK-10 - KIT EVAL APPL MASS STORAGEAT89STK-05 - KIT STARTER FOR AT89C5131
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

21.8.2
21.8.3
134
AT89C5130A/31A-M
Resume
Upstream Resume
The stop of the 48 MHz clock from the PLL should be done in the following order:
When the USB controller is in Suspend state, the Resume detection is active even if all the
clocks are disabled and if the C51 is in Idle or Power-down mode. The WUPCPU bit is set by
hardware when a non-idle state occurs on the USB bus. This triggers an interrupt if enabled.
This interrupt wakes up the CPU from its Idle or Power-down state and the interrupt function is
then executed. The firmware will first enable the 48 MHz generation and then reset to 0 the
SUSPCLK bit in the USBCON register if needed.
The firmware has to clear the SPINT bit in the USBINT register before any other USB operation
in order to wake up the USB controller from its Suspend mode.
The USB controller is then re-activated.
Figure 21-11. Example of a Suspend/Resume Management
A USB device can be allowed by the Host to send an upstream resume for Remote Wake Up
purpose.
1. Clear suspend interrupt bit in USBINT (required to allow the USB pads to enter power
2. Enable USB resume interrupt.
3. Disable of the 48 MHz clock input of the USB controller by setting to 1 the SUSPCLK bit
4. Disable the PLL by clearing the PLLEN bit in the PLLCON register.
5. Make the CPU core enter power down mode by setting PDOWN bit in PCON.
down mode).
in the USBCON register.
Detection of a SUSPEND State
Detection of a RESUME State
WUPCPU
SPINT
microcontroller in Power-down
Clear WUPCPU Bit
USB Controller Init
Clear SUSPCLK
Set SUSPCLK
Clear SPINT
Disable PLL
Enable PLL
4337K–USB–04/08