AT89C5131A-PUTUM Atmel, AT89C5131A-PUTUM Datasheet - Page 49

• Manufacturer Part Number: AT89C5131A-PUTUM
• Description: IC 8051 MCU FLASH 32K USB 32QFN
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5131A-PUTUM

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: LED, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Core: 8051
• Processor Series: AT89x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 48 MHz
• Data Ram Size: 1.25 KB
• Number Of Programmable I/os: 34
• Number Of Timers: 16 bit
• Operating Supply Voltage: 2.7 V to 5.5 V
• Mounting Style: SMD/SMT
• Height: 0.95 mm
• Interface Type: 2-Wire, EUART, SPI, USB
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCUAT89STK-10 - KIT EVAL APPL MASS STORAGEAT89STK-05 - KIT STARTER FOR AT89C5131
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

11.5.2
4337K–USB–04/08
Low Pin Count Hardware Conditions (QFN32)
Figure 11-4. Hardware conditions typical sequence during power-on.
Low pin count products do not have PSEN signal, thus for these products, the bootloader is
always executed after reset thanks to the BLJB bit. The Hardware Condition are detected at the
begining of the bootloader execution from reset.
The default factory Hardware Condition is assigned to port P1.
In order to offer the best flexibility, the user can define its own Hardware Condition on one of the
following Ports:
The Hardware Condition configuration are stored in three bytes called P1_CF, P3_CF, P4_CF.
These bytes can be modified by the user through a set of API or through an ISP command.
Note:
See a detailed description in the applicable Document.
• P1 must be equal to FEh
• Port1
• Port3
• Port4 (only bit0 and bit1)
– Datasheet Bootloader USB AT89C5131.
1. The BLJB must be at 0 (programmed) to be able to restart the bootloader.
2. BLJB can always be changed by the means of API, whether it's a low or high pin count pack-
age.But for a low pin count version, if BLJB=1, no ISP via the Bootloader is further possible
(because the HW conditions are never evaluated, as described in the USB Bootloader
Datasheet). To go back to ISP, BLJB needs to be changed by a parallel programmer(or by the
APIs).
VCC
PSEN
RST
AT89C5130A/31A-M
49