AT91SAM7S321-AU Atmel, AT91SAM7S321-AU Datasheet - Page 655

• Manufacturer Part Number: AT91SAM7S321-AU
• Description: IC ARM7 MCU FLASH 32K 64LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7S321-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, I2S, SPI, SSC, TWI, UART, USB
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 10 bit
• Operating Supply Voltage: 1.8 V to 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7S-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7S-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Controller Family/series: AT91SAM7xxxx
• No. Of I/o's: 32
• Ram Memory Size: 8KB
• Cpu Speed: 55MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7S-EK - KIT EVAL FOR ARM AT91SAM7S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

40.10.12.3
40.10.12.4
40.10.12.5
40.10.13 Voltage Regulator
40.10.13.1
40.10.13.2
6175K–ATARM–30-Aug-10
USART: XOFF Character Bad Behavior
USART: RXBRK Flag Error in Asynchronous Mode
USART: DCD is active High instead of Low
Voltage Regulator: Current Consumption in Deep Mode
Voltage Regulator: Load Versus Temperature
Don't use the PDC in transmit mode and do not fill US_THR before TXEMPTY is set at 1.
The XOFF character is sent only when the receive buffer is detected full. While the XOFF is
being sent, the remote transmitter is still transmitting. As only one Holding register is available in
the receiver, characters will be lost in reception. This makes the software handshaking function-
ality ineffective.
None.
In receiver mode, when there are two consecutive characters (without timeguard in between),
RXBRK is not taken into account. As a result, the RXBRK flag is not enabled correctly and the
frame error flag is set.
Constraints on the transmitter device connected to the AT91SAM7S USART receiver side:
The transmitter may use the timeguard feature or send two STOP conditions. Only one STOP
condition is taken into account by the receiver state machine. After this STOP condition, as there
is no valid data, the receiver state machine will go in idle mode and enable the RXBRK flag.
The DCD signal is active at High level in the USART Modem Mode.
DCD should be active at Low level.
Add an inverter.
Current consumption in Deep Mode is maximum 60 µA instead of 25 µA.
Due to current rejection from VDDIN to VDDCORE, the current consumption in Deep Mode can-
not be guaranteed. Instead, 60 µA is guaranteed whatever the condition.
None.
Maximum load is 50 mA at 85 °C (instead of 100 mA).
Maximum load is 100 mA at 70°C.
None.
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
AT91SAM7S Series Preliminary
655