AT91SAM7X128B-AU Atmel, AT91SAM7X128B-AU Datasheet - Page 526

• Manufacturer Part Number: AT91SAM7X128B-AU
• Description: IC MCU 128KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X128B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: JTAG, SPI, UART
• Maximum Clock Frequency: 55 MHz
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7X-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7X-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 62
• Ram Memory Size: 32KB
• Cpu Speed: 55MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Cpu Family: 91S
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 55MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Figure 36-16. Producer / Consumer Model
PUSH MODEL
Producer
Consumer
Indication(s)
Request
CAN Data Frame
PULL MODEL
Producer
Consumer
Indications
CAN Remote Frame
Request(s)
Response
CAN Data Frame
Confirmation(s)
In Pull Mode, a consumer transmits a remote frame to the producer. When the producer
receives a remote frame, it sends the answer accepted by one or many consumers. Using trans-
mit and receive mailboxes, a consumer must dedicate two mailboxes, one in Transmit Mode to
send remote frames, and at least one in Receive Mode to capture the producer’s answer. The
same structure is applicable to a producer: one reception mailbox is required to get the remote
frame and one transmit mailbox to answer.
Mailboxes can be configured in Producer or Consumer Mode. A lonely mailbox can handle the
remote frame and the answer. With 8 mailboxes, the CAN controller can handle 8 independent
producers/consumers.
36.7.3.7
Producer Configuration
A mailbox is in Producer Mode once the MOT field in the CAN_MMRx register has been config-
ured. Message ID and Message Acceptance masks must be set before Receive Mode is
enabled.
After Producer Mode is enabled, the MRDY flag in the CAN_MSR register is automatically set
until the first transfer command. The software application prepares data to be sent by writing to
the CAN_MDHx and the CAN_MDLx registers, then by setting the MTCR bit in the CAN_MCRx
register. Data is sent after the reception of a remote frame as soon as it wins the bus arbitration.
The MRDY flag remains at zero as long as the message has not been sent or aborted. No
access to the mailbox data register can be done while MRDY flag is cleared. An interrupt is
pending for the mailbox while the MRDY flag is set. This interrupt can be masked according to
the mailbox flag in the CAN_IMR global register.
If a remote frame is received while no data are ready to be sent (signal MRDY set in the
CAN_MSRx register), then the MMI signal is set in the CAN_MSRx register. This bit is cleared
by reading the CAN_MSRx register.
The MRTR field in the CAN_MSRx register has no meaning. This field is used only when using
Receive and Receive with Overwrite modes.
SAM7X512/256/128 Preliminary
526
6120I–ATARM–06-Apr-11