ST72F321BAR6T6 STMicroelectronics, ST72F321BAR6T6 Datasheet - Page 159
![MCU 8BIT 32KB FLASH/ROM 64-LQFP](/photos/12/15/121504/stmicroelectronics-64-lqfp_sml.jpg)
ST72F321BAR6T6
Manufacturer Part Number
ST72F321BAR6T6
Description
MCU 8BIT 32KB FLASH/ROM 64-LQFP
Manufacturer
STMicroelectronics
Series
ST7r
Datasheet
1.ST72F321BK6T6.pdf
(187 pages)
Specifications of ST72F321BAR6T6
Core Processor
ST7
Core Size
8-Bit
Speed
8MHz
Connectivity
I²C, SCI, SPI
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
48
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
3.8 V ~ 5.5 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-LQFP
Processor Series
ST72F3x
Core
ST7
Data Bus Width
8 bit
Data Ram Size
1 KB
Interface Type
I2C, SCI, SPI
Maximum Clock Frequency
8 MHz
Number Of Programmable I/os
48
Number Of Timers
2
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Development Tools By Supplier
ST7232X-EVAL, ST7232X-SK/RAIS, ST72321B-D/RAIS, ST7MDT20-DVP3, ST7MDT20J-EMU3, ST7MDT20M-EMU3, STX-RLINK
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 16 Channel
For Use With
497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Other names
497-5582
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ST72F321BAR6T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
CONTROL PIN CHARACTERISTICS (Cont’d)
Figure 86. RESET pin protection when LVD is enabled.
Figure 87. RESET pin protection when LVD is disabled.
Note 1:
Note 2: When the LVD is enabled, it is recommended not to connect a pull-up resistor or capacitor. A 10nF pull-down
capacitor is required to filter noise on the reset line.
Note 3: In case a capacitive power supply is used, it is recommended to connect a 1MΩ pull-down resistor to the RESET
pin to discharge any residual voltage induced by the capacitive effect of the power supply (this will add 5µA to the power
consumption of the MCU).
Note 4: Tips when using the LVD:
Required
– The reset network protects the device against parasitic resets.
– The output of the external reset circuit must have an open-drain output to drive the ST7 reset pad. Otherwise the
– Whatever the reset source is (internal or external), the user must ensure that the level on the RESET pin can go
– Because the reset circuit is designed to allow the internal RESET to be output in the RESET pin, the user must en-
– 1. Check that all recommendations related to reset circuit have been applied (see notes above).
– 2. Check that the power supply is properly decoupled (100nF + 10µF close to the MCU). Refer to AN1709 and
– 3. The capacitors connected on the RESET pin and also the power supply are key to avoid any start-up marginality.
EXTERNAL
EXTERNAL
CIRCUIT
device can be damaged when the ST7 generates an internal reset (LVD or watchdog).
below the V
internally.
sure that the current sunk on the RESET pin is less than the absolute maximum value specified for I
section 12.2.2 on page
AN2017. If this cannot be done, it is recommended to put a 100nF + 1MΩ pull-down on the RESET pin.
In most cases, steps 1 and 2 above are sufficient for a robust solution. Otherwise: replace 10nF pull-down on the
RESET pin with a 5µF to 20µF capacitor.
RESET
USER
RESET
Required
IL
max. level specified in
0.01μF
0.01μF
139.
1MΩ
Optional
(note 3)
section 12.9.1 on page
ST72321BRx, ST72321BARx ST72321BJx, ST72321BKx
V
V
DD
DD
R
R
ON
ON
Filter
Filter
158. Otherwise the reset will not be taken into account
1)2)3)4)
1)
GENERATOR
GENERATOR
PULSE
PULSE
INTERNAL
RESET
INTERNAL
RESET
WATCHDOG
WATCHDOG
LVD RESET
INJ(RESET)
ST72XXX
ST72XXX
159/187
in