MCF5272VM66J Freescale Semiconductor, MCF5272VM66J Datasheet - Page 345

• Manufacturer Part Number: MCF5272VM66J
• Description: IC MCU 166MHZ 196MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF527xr

Specifications of MCF5272VM66J

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART, USB
• Peripherals: DMA, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (4K x 32)
• Program Memory Type: ROM
• Ram Size: 1K x 32
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 196-MAPBGA
• Processor Series: MCF527x
• Core: ColdFire V2
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: I2C, UART, Ethernet, SPI, USB, QSPI
• Maximum Clock Frequency: 166 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 1.4 V to 1.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: NNDK-MOD5272-KIT, NNDK-MOD5270-KIT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

14.4.3
The QSPI supports programmable delays for the QSPI_CS signals before and after a transfer. The time
between QSPI_CS assertion and the leading QSPI_CLK edge, and the time between the end of one transfer
and the beginning of the next, are both independently programmable.
The chip select to clock delay enable (DSCK) bit in command RAM, QCR[DSCK], enables the
programmable delay period from QSPI_CS assertion until the leading edge of QSPI_CLK. QDLYR[QCD]
determines the period of delay before the leading edge of QSPI_CLK. The following expression
determines the actual delay before the QSPI_CLK leading edge:
QSPI_CS-to-QSPI_CLK delay = QCD/CLKIN frequency
QCD has a range of 1–127.
When QCD or DSCK equals zero, the standard delay of one-half the QSPI_CLK period is used.
The delay after transmit enable (DT) bit in command RAM enables the programmable delay period from
the negation of the QSPI_CS signals until the start of the next transfer. The delay after transfer can be used
to provide a peripheral deselect interval. A delay can also be inserted between consecutive transfers to
allow serial A/D converters to complete conversion. There are two transfer delay options: the user can
choose to delay a standard period after serial transfer is complete or can specify a delay period. Writing a
value to QDLYR[DTL] specifies a delay period. The DT bit in command RAM determines whether the
standard delay period (DT = 0) or the specified delay period (DT = 1) is used. The following expression
is used to calculate the delay:
Delay after transfer = 32 × QDLYR[DTL] /CLKIN frequency (DT = 1)
where QDLYR[DTL] has a range of 1–255.
A zero value for DTL causes a delay-after-transfer value of 8192/CLKIN frequency.
Standard delay after transfer = 17/CLKIN frequency (DT = 0)
Receiving devices need at least the standard delay (DT=0) between successive transfers for long data
streams because the QSPI module requires time to load a transmit RAM entry for transfer. If CLKIN is
operating at a slower rate, the delay between transfers must be increased proportionately.
Freescale Semiconductor
Transfer Delays
Table 14-2. QSPI_CLK Frequency as Function of CPU Clock and Baud Rate
QMR [BAUD]
255
16
32
2
4
8
MCF5272 ColdFire
®
66 MHz
Integrated Microprocessor User’s Manual, Rev. 3
16,500,000
8,250,000
4,125,000
2,062,500
1,031,250
129,412
48 MHz
12,000,000
6,000,000
3,000,000
1,500,000
750,000
94,118
CPU Clock
Queued Serial Peripheral Interface (QSPI) Module
33 MHz
8,250,000
4,125,000
2,062,500
1,031,250
515,625
64,706
20 MHz
5,000,000
2,500,000
1,250,000
625,000
312,500
39,216
14-7