ATMEGA2560R231-CU Atmel, ATMEGA2560R231-CU Datasheet - Page 233

• Manufacturer Part Number: ATMEGA2560R231-CU
• Description: BUNDLE ATMEGA2560/RF231 PBGA
• Manufacturer: Atmel

Specifications of ATMEGA2560R231-CU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
• Data Interface: PCB, Surface Mount
• Memory Size: 256kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 100-CBGA and 32-QFN
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 256 KB
• Data Ram Size: 8 KB
• Development Tools By Supplier: ATAVRRZ541, ATAVRRAVEN, ATAVRRZRAVEN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Power - Output: -
• Operating Temperature: -
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

22.2.1
22.3
2549M–AVR–09/10
SPI Data Modes and Timing
Clock Generation
A comparison of the USART in MSPIM mode and the SPI pins is shown in
240.
The Clock Generation logic generates the base clock for the Transmitter and Receiver. For
USART MSPIM mode of operation only internal clock generation (that is, master operation) is
supported. The Data Direction Register for the XCKn pin (DDR_XCKn) must therefore be set to
one (that is, as output) for the USART in MSPIM to operate correctly. Preferably the DDR_XCKn
should be set up before the USART in MSPIM is enabled (that is, TXENn and RXENn bit set to
one).
The internal clock generation used in MSPIM mode is identical to the USART synchronous mas-
ter mode. The baud rate or UBRRn setting can therefore be calculated using the same
equations, see
Table 22-1.
Note:
There are four combinations of XCKn (SCK) phase and polarity with respect to serial data, which
are determined by control bits UCPHAn and UCPOLn. The data transfer timing diagrams are
shown in
the XCKn signal, ensuring sufficient time for data signals to stabilize. The UCPOLn and
UCPHAn functionality is summarized in
these bits will corrupt all ongoing communication for both the Receiver and Transmitter.
Table 22-2.
Operating Mode
Synchronous Master
mode
UCPOLn
BAUD
f
UBRRn
OSC
0
0
1
1
1. The baud rate is defined to be the transfer rate in bit per second (bps).
Figure 22-1 on page
Equations for Calculating Baud Rate Register Setting
UCPOLn and UCPHAn Functionality-
Table
UCPHAn
22-1.
Baud rate (in bits per second, bps).
System Oscillator clock frequency.
Contents of the UBRRnH and UBRRnL Registers, (0-4095).
0
1
0
1
Equation for Calculating Baud
BAUD
234. Data bits are shifted out and latched in on opposite edges of
ATmega640/1280/1281/2560/2561
=
SPI Mode
Rate
-------------------------------------- -
2 UBRRn
(
0
1
2
3
(1)
f
OSC
Table
+
22-2. Note that changing the setting of any of
1
)
Sample (Rising)
Sample (Falling)
Leading Edge
Setup (Rising)
Setup (Falling)
Equation for Calculating
UBRRn
UBRRn Value
=
------------------- - 1
2BAUD
f
OSC
Table 22-4 on page
Sample (Falling)
Sample (Rising)
Setup (Falling)
Setup (Rising)
Trailing Edge
–
233